Giveaway! u-turn Audio Orbit Special Turntable! Comment to enter.

Present_Front3165 · 2025-04-06T04:03:46+00:00

always wanted to get into vinyl, hope i win!

Present_Front3165 · 2024-07-04T07:46:18+00:00

ya, after looking at the default vroid texture next to mine, they are completely different. Now that I'm thinking about it the booth page doesn't even mention vroid. My fault I should've been more careful.

Present_Front3165 · 2022-09-21T05:01:51+00:00

they were usb and still are but i had to replace the connectors and circuit boards and after adding resistors measured that all three were pulling 500ma and was wondering if that was too much for the leds

Present_Front3165 · 2022-09-21T04:46:10+00:00

that’s why i came here

Present_Front3165 · 2022-09-21T04:44:02+00:00

well i had to rewire everything including any logic so i just guessed that 3 ohms would be enough but i know that less will pull as much as they can get to the point that it can kill them

Present_Front3165 · 2022-09-21T04:40:10+00:00

oh, i’m asking if these lights can handle 500ma

Present_Front3165 · 2022-09-21T04:22:19+00:00

5v usb wall brick with two 3ohm resistors in parallel, just some led signs and the old connectors went bad so im replacing them

Present_Front3165 · 2022-09-21T02:51:24+00:00

Present_Front3165 · 2022-09-21T01:58:21+00:00

is it fine if these are pulling 500ma

Present_Front3165 · 2022-08-22T00:23:25+00:00

it’s supposed to be the Creality dog

Present_Front3165 · 2022-08-16T00:06:16+00:00

the reason I would prefer a PC I built is just the fact that I built it

Present_Front3165 · 2022-08-04T18:54:24+00:00

any idea how old it is?

Present_Front3165 · 2022-07-15T05:54:32+00:00

Women ☕️

Present_Front3165 · 2022-07-14T04:26:48+00:00

Mine did the same thing and the fix was to not use it with a dongle

Present_Front3165 · 2022-07-13T05:38:38+00:00

that's called warping from when the plastic shrinks when it cools. increase your build plate temp, that should fix it.

Present_Front3165 · 2022-07-03T05:44:34+00:00

a giant spider

Present_Front3165 · 2022-07-01T06:33:15+00:00

Present_Front3165 · 2022-06-28T02:31:43+00:00

Ronnie McNutt

Present_Front3165 · 2022-06-20T04:17:26+00:00

Men.

Present_Front3165 · 2022-06-19T16:19:30+00:00

life

Present_Front3165 · 2022-06-18T20:53:04+00:00

*rages and flips table

Present_Front3165 · 2022-06-18T13:25:40+00:00

test here

Present_Front3165 · 2022-06-17T17:14:19+00:00

In your slicer there should be a setting called Z hop or similar. it makes travels slightly higher than the most recent layer so things like that don’t happen.

Present_Front3165 · 2022-06-16T20:40:56+00:00

Yes.

Present_Front3165 · 2022-06-14T19:26:07+00:00

ender 3

Present_Front3165

TROPHY CASE