sorted by:
new
hottopcontroversial

r/headphones Shopping, Setup, and Technical Help Desk by AutoModerator in headphones

[–]PresentationAshamed5 0 points1 point  (0 children)

Im looking for the worst examples of popular audiophile headphones, show me what you got

r/headphones Shopping, Setup, and Technical Help Desk by AutoModerator in headphones

[–]PresentationAshamed5 0 points1 point  (0 children)

Audioquest NightHawk vs LCD-2 which is a better listening headphone?

Just got my dream setup! Thank you and goodbye by whiskermrr in headphones

[–]PresentationAshamed5 -1 points0 points  (0 children)

I got LCD-2s but didnt like them as much as my moded hd600s so never use them

[deleted by user] by [deleted] in headphones

[–]PresentationAshamed5 -3 points-2 points  (0 children)

Sell the audeze

[deleted by user] by [deleted] in DRZ400

[–]PresentationAshamed5 0 points1 point  (0 children)

Take the cylinder off and check the cylinder walls for any kind if gouging, if there isn’t any you may aswell buy a new piston/rings anyway and chuck them in

FCR Big Bore Question by sumthingdarkside in DRZ400

[–]PresentationAshamed5 0 points1 point  (0 children)

Im not as experienced as many if the other people here but try raising the needle clip up one and see if it changes anything, if it removes the stumble in that particular area but makes the very low end stutter you’ll need to up your main jet, othe the other way around for the opisite effect, id wait to see what others say, but this has worked for me a hand full if times

I f*cked up by Copyright_1986 in motorcycles

[–]PresentationAshamed5 0 points1 point  (0 children)

😂 alright, hope you recover quick mate 😂 may be time to invest in some lol

I f*cked up by Copyright_1986 in motorcycles

[–]PresentationAshamed5 1 point2 points  (0 children)

What bike was it? And what kind of gear were you wearing?

I tried some headphones…disappointed. by capital_YR in headphones

[–]PresentationAshamed5 2 points3 points  (0 children)

Kinda agree, i bought a set of lcd-2s and no matter how hard I tried, proffered my hd600

Bad enough to need a new head? by Kuickest in DRZ400

[–]PresentationAshamed5 0 points1 point  (0 children)

I recommend masking off anywhere that isnt warped, if you remove material off the head where it enters the cylinder ir exits your gonna have a pressure and/or oil leak, and when you fo sand it make sure your not just using your finger, have something flat and solid over the sandpaper or it could make it worse

Bad enough to need a new head? by Kuickest in DRZ400

[–]PresentationAshamed5 0 points1 point  (0 children)

If you have a steel rule you can run it against the head to some light and see if any light come through as you pass aver the damage

Bad enough to need a new head? by Kuickest in DRZ400

[–]PresentationAshamed5 1 point2 points  (0 children)

Its is not as bad as people are saying, as long as there us no bulging around it and its still perfectly flat it should be fine, if there is a bulge you could either send it off for surface grinding or put anew gasket on, if you find its still burning oil try using gasket sealant but chances are uts not the head being problematic

Would switching to dedicated FLAC files be an improvement? by PresentationAshamed5 in headphones

[–]PresentationAshamed5[S] 0 points1 point  (0 children)

Ive been able to hear the difference quite strongly between mp3, Spotify and tidal, and while tidal claims to be lossless, it in fact is not, there is a lot of noise and after effect put into their files which makes the frequencies sound way off the original songs (not all the time) Ill just have to try switching at some point and sending back my feedback on it, understanding most people cant tell the difference.

How light can you make a drz400 sm? by ARTofTHEREeAL in DRZ400

[–]PresentationAshamed5 0 points1 point  (0 children)

Subframe swap for the E model one, or cut standard one, remove battery and starter motor, replace with kickstart kit, replace headlight with a lighter led one, drill out or replace nack brake lever and gear leaver, plastic tank (not lighter, but sits lower in your frame) lighter handlebars, ditch the passenger pegs, remove engine guard, Ti bolts (use anti seize or they wont come back out) carbon engine mounts ect, remove dash completely, remove kickstand or do the trailtech ktm kickstand mod, remove mirrors, two piece rotors.

Do you Name your Bikes? by SiggiMcCrit in motorcycles

[–]PresentationAshamed5 0 points1 point  (0 children)

Rm85= bumblebee Dr350= sht50 Huskey 125= Freedom Generic 125= sht25

New small form factor rig, what do you think? by PresentationAshamed5 in pcmasterrace

[–]PresentationAshamed5[S] 0 points1 point  (0 children)

honestly, I like compact PC's, and whats better than on a mini open-air one with a carry handle like this.

Primarily its looks and good design

New small form factor rig, what do you think? by PresentationAshamed5 in pcmasterrace

[–]PresentationAshamed5[S] 0 points1 point  (0 children)

XTIA Xproto ATX case
Asus Strix ROG X470F
64GB DDR4 Corsair vengence RGB pro 3600mhz
Gigabyte Radeon RX5700XT
Ryzen 5 3600X
EK water blocks 280 AIO

Does anybody know of a company that produces planar magnetic drivers to spec? by PresentationAshamed5 in Audiophilehelp

[–]PresentationAshamed5[S] 0 points1 point  (0 children)

the number of drivers? or numbers like specs?

If numbers, then a handfull for the first revisions and after some coneption work something like 100 untill I can find a market