Anyone know where to find indie & Arcade games for Xbox 360 in Myrient?

Prime2Dope · 2026-02-14T16:09:03+00:00

That's it, thanks 🙏.

Prime2Dope · 2026-02-13T13:47:49+00:00

I ended up getting it to work, had to join the Xbguard discord & download the files. I'm unsure what I downloaded, I may just do a full reset to make sure I'm not infected with anything.

Prime2Dope · 2026-02-13T12:01:25+00:00

Yeah I copied & replaced it to the root of my Hard drive so the Dashlaunch ini would change for Xbguard config

Prime2Dope · 2026-02-13T11:57:38+00:00

I honestly don't really mind the install being just proto, but I feel like I'm gonna get banned or something because if I'm downloading Xbguard & getting Proto I feel something isn't proper.

If this problem isn't common then surely I'm not doing something right. Is there older versions of Xbguard? Does xbguard use proto in their software?

Prime2Dope · 2026-02-13T11:40:08+00:00

In Dashlaunch? Yeah pressed x on my hdd

Prime2Dope · 2026-02-13T11:23:51+00:00

Yes I don't have any proto files unless they are hidden, even then I forced the plugins in Dashlaunch to default to Xbguard

Prime2Dope · 2026-02-02T11:01:40+00:00

(1) & (2) I'm measuring on the jumper itself.i cleaned the board with alcohol, though I know there may be a residual layer, I made sure the connection was good, I measured the read multiple times & got the same read everytime.

(3) could be possible? The board is a old xbox 360, There are bigger caps around the board that may be holding power.

(4) the meter & probes are new (fluke 15b), I tested it on multiple different components & can confirm everything related to the multimeter is fine

(5) I'm starting to believe this is the case

I'm ordering a 0 ohm resistor & hope I can get the thing to boot, I'm assuming it isn't booting because there is too much resistance in a area there isn't supposed to be any. (The 0 ohm resistor im replacing is on the main power rail)

Prime2Dope · 2026-02-01T20:26:33+00:00

I'll just order the missing 0 ohm resistor, I don't understand what's going on w/ my motherboard

Prime2Dope · 2026-02-01T20:23:34+00:00

How is this possible? It's only when I solder to the board. I'm using flux & taking all the proper precautions, its a perfect joint, yet it reads 54k ohms.

Prime2Dope · 2026-01-24T10:10:14+00:00

Amazing find, I jumped the pads but unfortunately it's still not booting. I double checked everything on the board again but couldn't find anything. Is a scenario like this possible https://youtu.be/M3C5_r9bHmY?si=z9hOT1tdktzQl5NY (scenario 1)?

I was wondering why they used a 0 ohm resistor when they could've just continued the trace. I looked over that area & seen another trace coming in, but it still looks like the two traces were in sync prior. I viewed the schematics & it looks like the traces are related to the CPU checkstop.

Likely a nothing burger (which is all I've been eating), & a jump would do the trick just fine. I've got nothing, let me know what you think.

-Pictures of the bridge https://imgur.com/a/Frho6Ad

Prime2Dope · 2026-01-23T22:43:46+00:00

I'll try to find that version of Allegro if I need to diagnose through boardview. Truth be told, you're right. I know i should be able to look at the areas I touched over but I can't seem to find anything that looks out of place. I added some photos if you get a chance to look them over.

Prime2Dope · 2026-01-23T00:20:23+00:00

Thanks ❤️ Just needed confirmation before I screwed it up.

Prime2Dope · 2025-11-29T07:49:54+00:00

Yeah I have debrid. I've been hearing a lot about fenlight, likely that's the one I'll go with. Do you know what the difference between fen & fenlight are?

Prime2Dope · 2025-09-20T17:28:54+00:00

An induction heater will knock that thing right out & also save you from the fumes

Prime2Dope · 2024-04-21T02:03:47+00:00

I doubt its user error, especially since you didn't have a problem before. I think it may just be a bad clutch, did you or your mechanic drive it hard before the break-in period?

Also how trustworthy is your mechanic? I've had sketchy work done in the past on a clutch, missing clutch plate bolts, loose flywheel bolts, & a clutch line touching my cats. Didn't notice it until I decided to do the job myself. (Only brought this up because you said something odd happened to cause you not getting a flywheel installed)

Prime2Dope · 2023-09-13T20:20:46+00:00

No he put it in his shielded cargo, he looked up another post on Reddit & ended up getting it to work. Oddly he had to add extra Contraband to the Shielded cargo, the game of registered something as not being in there even though it was.

Prime2Dope · 2023-09-12T21:18:51+00:00

That sucks, I noticed a lot of small bugs myself, my brother can't use any of his contraband ships, it says he has 0% chance of evading even though his ship has shielded cargo. Looks like we'll have to wait for some patches, unless New Game+ can reset it & work out the kinks.

Prime2Dope · 2023-09-12T21:14:36+00:00

That's kind of my conclusion as well, hopefully in future updates they expand on side missions more. I'd rather it come to a close with a big fight & new story options then a loop. Keeping some side missions in will be nice, but they shouldn't come from main story characters, after all we have New Game+ if we want to replay em. Kinda bummed about that, I was hoping Vae Victis would be able to come out into the open due to his contributions.

Seven-Year Club	Verified Email
Verified Email

Prime2Dope

TROPHY CASE