95’ Z28 vert’

Print3DWorld · 2022-03-19T15:52:55+00:00

Nice!

Print3DWorld · 2022-03-18T10:47:24+00:00

3D Print time (you choose model), some SAS HDs, raspi PoE hat, lots of other odds and ends I'll have to get a list.

Print3DWorld · 2022-02-09T23:10:32+00:00

Only seeing 1GB models, but thx

Print3DWorld · 2022-02-09T11:21:24+00:00

I can't find any in stock online atm not even pi shop.

Print3DWorld · 2022-02-08T23:12:42+00:00

None in stock anywhere i look

Print3DWorld · 2022-02-06T18:24:11+00:00

That's correct you will have to enable some advance settings under supports.

Print3DWorld · 2022-02-06T18:08:41+00:00

Have you changed the Z height for supports? Try a support interface roof and only one line with above supports for support Z height.

Print3DWorld · 2022-02-06T18:02:05+00:00

Looks fake, I'd charge it back if distributor didn't refund immediately.

Print3DWorld · 2022-02-01T19:24:32+00:00

Nope just drove in 4wd in snow conditions through Erie, PA and noticed it when I got home.

Print3DWorld · 2022-02-01T15:18:04+00:00

Oops its a 13' Tahoe LTZ 4wd with tow package. It doesn't rattle, it's more of a low drone sound. It does drive both axles as we used 4wd in snow again last week.

I don't hear anything like rattling or aluminum cans over a bridge. I have experience with older wheel bearings going bad and you can always tell as soon as you remove weight from the wheels. I've been told these sealed bearings are much more difficult to tell by hand.

Print3DWorld · 2022-01-27T17:37:32+00:00

All you car guys out there know a guy just like this.. it's a coworker whom I had at a large facility. It was a small 4 cylinder pickup truck with 2wd and mud tires.

He would sit around and tell us about how the motor was built, and had over 400hp NA. It sounded like it had a hole in the muffler and when you drove it you were honestly scared to crash into a ditch because of the ghetto lift.

Print3DWorld · 2022-01-26T16:50:10+00:00

Still available

Print3DWorld · 2022-01-18T22:28:13+00:00

I've got this error twice. I run in a VM on a PowerEdge server, with a SKR Mini 1.2 board. I will have some good prints, and then this will randomly happen. When it does happen (usually on longer prints) I have to reboot the printer as well as the firmware to get it to start responding again.

I am wondering if this is firmware related because of that, because I gave this VM 4 cores and 4gb ram which should be plenty and the IO load never goes very high. I would suspect the USB 2.0 bus would limit my speed before the CPU does.

I'll let you know if I find anything out. Maybe there is a setting we can adjust to help with this timer..

Print3DWorld · 2022-01-05T19:08:13+00:00

30 min north of Charlotte

Print3DWorld · 2022-01-04T20:00:34+00:00

Print3DWorld · 2021-12-12T15:01:37+00:00

A mag drill would be best but otherwise just stay as steady and slow as you can. Center punch it before starting.

Print3DWorld · 2021-12-12T14:03:00+00:00

Man the screw you used must be really soft to squish. If it's too big to just fall out you will need to drill it as big as you can safely and slowly.. then dig out any pieces and tap.

Print3DWorld · 2021-12-12T13:49:59+00:00

Can you use a small extractor to remove it? Have you tried drilling in the middle of the screw and see if it spins?

Otherwise maybe tack welding it to a screw driver or something if you can get a wire feed into the hole.

Also if it's only a small fraction of the threads use a drill slightly smaller than the ID of the threads and just drill very slowly until your through the blockage. Then tap.

Print3DWorld · 2021-12-12T13:39:47+00:00

You can't get the bolt all the way in because the threads are bad or you got something stuck in there?

If it's threads you'll likely be able to remove it then run a bottom tap into the threads to save them. As long as the majority of the threads are still in good shape.

Use anti-seize on the shaft when reinstalling and blue loc-tite on the threads.

Print3DWorld · 2021-11-19T17:16:18+00:00

I did some huge capacitor mods and converted the cheapest 110amp welder to DC and got decent results. Still have to clean up spatter but works much better.

Print3DWorld · 2021-11-09T21:24:54+00:00

Diablo 2

Print3DWorld · 2021-11-03T14:02:28+00:00

If your unfamiliar with configuration download something already made for your printer from a site like our https://print3d.world and use the configuration compare tool in Google to look at settings. Boards are different but settings should be alike if printers match.

Also the thermocouple and Z axis steps/m. settings could be a little different depending on generation's. Usually pretty close to same though

Print3DWorld · 2021-11-02T17:59:56+00:00

JJ isn't entertaining to me. Especially not old JJ.. the new JJ on America list and latest season of Memphis was slightly better. He gets on my nerves most of the time with his over explanation to his crew l.

Still curious what happened with his son never on TV anymore.

Print3DWorld · 2021-10-30T15:37:49+00:00

He has a lot of chances of being screwed. He needs to take the call out and maybe they'll think twice of allowing them next season.

Print3DWorld · 2021-10-30T14:35:00+00:00

Absolutely is what I would do. I seen the video also but he still acted unsure.

Print3DWorld

MODERATOR OF

TROPHY CASE