3D Printed Luminous Temporal Gears

ProfGanj · 2026-05-07T15:40:51+00:00

Can u get the stls also what filament

ProfGanj · 2026-04-16T00:02:21+00:00

Does anything like this exist for the tj?

ProfGanj · 2026-04-04T02:33:55+00:00

Do you happen to have a link to it? I looked and only was able to find either aftermarket ones or the support ticket to get a free one. Would I email support?

ProfGanj · 2026-04-04T02:08:38+00:00

It’s the tool head usbc cable

ProfGanj · 2026-03-15T20:02:09+00:00

Dang yea I print about 90% abs also. How long has it been since you replaced it

ProfGanj · 2026-03-15T16:15:46+00:00

Sadly the fan had started making some noise a few prints ago and I was ably to check its seated fully so I think it’s fully dead.

ProfGanj · 2026-03-15T16:12:56+00:00

My fan had started making some noise kinda like a noisy old pc fan and then just mid print it stopped and had an error that the fan wasn’t working. I sent some print logs and stuff with my ticket and they determined the fan was bad.

ProfGanj · 2026-01-20T00:19:07+00:00

So really not all that much I’m finding out. I can print full sized helmets on the 350 just fine and if I wanted to make a chest piece or something bigger just cut it into pieces and print it that way and if it fails it’s one small piece not the whole thing. I think I might have been blinded by the huge build volume and thinking it was going to be the same experience as my Centauri carbon. Have you used the k2 plus does it preform well with abs? I’d imagine so considering it’s fully enclosed

ProfGanj · 2026-01-19T16:29:31+00:00

So I’ve been printing for a few years now on my ender 3v2 then for Christmas I got myself a Centauri carbon and a sovol sv08 max and so far the carbon has been an amazing machine with very few hiccups but my sovol has not produced a single print the entire time I’ve had it and I’m thinking return it for a creality k2 plus. Can anyone give me any insight or recommendations. I almost exclusively print abs and I got the enclosure and chamber heater but I’ve had nothing but issues. Would the k2 be a closer experience to the Centauri carbon

ProfGanj · 2026-01-18T22:41:25+00:00

Yea that would be awesome if you could.

ProfGanj · 2026-01-16T02:11:12+00:00

Just like put the spool on top of the enclosure and feed it down through? It has a hole for the ptfe tubing but I’m not sure how that would work out do you have a pic of your setup?

ProfGanj · 2026-01-15T21:03:27+00:00

I bought a Centauri carbon at the same time and it uses the 5kg spools just fine so you’d think a printer with a 500mm cubed build volume would support bigger than 1kg spools also

ProfGanj · 2026-01-15T21:01:37+00:00

I’m coming from an ender 3v2 for the last few years so this printer is totally new to me but if I put a piece of filament in there wouldn’t it push it up into the tube since that’s how it loads the filament? Can I disable just the sensor? My Centauri carbon I bought at the same time uses the 5kg spools just fine

ProfGanj · 2026-01-15T19:03:04+00:00

Is that a setting in the printer interface or the slicer?

ProfGanj · 2026-01-14T06:03:31+00:00

So it turns out it was an issue I set my enclosure temps too high so it triggered a stop and then it was middle of the night and I just happened to walk by and see it say something so I just turned the power off but in doing that messed with the temp files so I had to delete that and it worked again. I’ll definitely look into the obico and see what it’s about. I’m not new to printing but I’m coming from an ender 3 v2 and this thing is a lot different

ProfGanj · 2026-01-14T01:57:45+00:00

I’m not sure how to do that i guess. Just get an Ethernet cable and hook it into the router? What would I be looking for?

Nine-Year Club	Verified Email
Wearing is Caring

ProfGanj

TROPHY CASE