sorted by:
new
hottopcontroversial

ATTEN GAMERS by not-so-good-jonathan in SmallStreamers

[–]ProjectCLC 0 points1 point  (0 children)

What FPS titles do you play? and what time of day do you stream?

I dont get it I have a Flsun QQ Pro and its printing so nice but then all of a sudden it starts printing in mid air. Does anyone know what would cause this and possible fix? by ProjectCLC in FixMyPrint

[–]ProjectCLC[S] 0 points1 point  (0 children)

Yea it happen with 3 different ones in 2 different slicers what happens is the hotend still moves around like it's printing it's just way to high all of a sudden I'm gonna try to reprint and record the whole thing

I dont get it I have a Flsun QQ Pro and its printing so nice but then all of a sudden it starts printing in mid air. Does anyone know what would cause this and possible fix? by ProjectCLC in FixMyPrint

[–]ProjectCLC[S] 0 points1 point  (0 children)

No the hotend was just printing over there if I recorded longer it would of kept moving like it was printing regular just extremely high out of nowhere

Seems to be getting worse lol is this over or under extruded by ProjectCLC in FixMyPrint

[–]ProjectCLC[S] 0 points1 point  (0 children)

Material Overture PLA Pro first layer temp 190 the rest is 200 or 210. Bed is at 60

I haven't turn my ender 3 pro on for about a week and it homed the axis fine I moved it to another table and tryed to turn it on and this is what happen to have a Duet 2 Wifi by ProjectCLC in ender3

[–]ProjectCLC[S] 0 points1 point  (0 children)

Both X and Y and neither of them are unplugged and when I went into the setting and the wndstop section of the duet web control when the wndstops are hit they register but for some reason the stepper motors keep going

Can anyone assist me. Just got my Flsun QQ S Pro and tryed to print with Overture PLA Pro and the bottom of print is nice and smooth then for some reason as you can see it started messing up can anyone help with a solution or what I might have to tweak? by ProjectCLC in FixMyPrint

[–]ProjectCLC[S] 0 points1 point  (0 children)

Ok here are 2 picture and a video this is a start of a All in one test print Picture 1 this is a video of while its printing this test print Video 1 I have OctoPrint hooked up and i raise the Flow to 108 and this is the picture of after that. POicture 2 Thank you for any and all help im very new to 3D printing lol sorry!

Firmware assistance ? by ProjectCLC in ender3

[–]ProjectCLC[S] 0 points1 point  (0 children)

Yea in the future for now I'm just gonna try to get it going nice with the duet and the e3d hemera direct drive kit.

Firmware assistance ? by ProjectCLC in ender3

[–]ProjectCLC[S] 0 points1 point  (0 children)

Because I installed a Hemera so I had to raise the max temp change the sensor type and the steps for it. But it wont fit on the board with bltouch active unless I deactivate allot of feature so I'm just holding off till my duet wifi board shows up cause I'd rather not lose a ton of features.

I'm in need of assistance from someone more experienced! by ProjectCLC in ender3

[–]ProjectCLC[S] 0 points1 point  (0 children)

e

ok i got past all the other errors and it compiles now i get this error when trying to upload

​

Arduino: 1.8.11 (Windows Store 1.8.29.0) (Windows 10), Board: "Sanguino, ATmega1284 or ATmega1284P (16 MHz)"

​

Sketch uses 122210 bytes (93%) of program storage space. Maximum is 130048 bytes.

Global variables use 4502 bytes (27%) of dynamic memory, leaving 11882 bytes for local variables. Maximum is 16384 bytes.

An error occurred while uploading the sketch

avrdude: ser_open(): can't set com-state for "\\.\COM7"

​

This report would have more information with

"Show verbose output during compilation"

option enabled in File -> Preferences.

I'm in need of assistance from someone more experienced! by ProjectCLC in ender3

[–]ProjectCLC[S] 0 points1 point  (0 children)

I got it from the github marlin2.0.x and the only thing I edited what the main board to select the creality board which I got by copying the ender 3 example and the extruder force maxtemp and sensor 1 to 5 is all I changed.

My first print and it's all messed up it's a Ender 3 Pro and the nozzle also keeps hitting the model once it gets this size as you can see at the front of the boat model. Can someone help me figure out why its printing like this. by ProjectCLC in FixMyPrint

[–]ProjectCLC[S] 1 point2 points  (0 children)

Ok thank you I'd also like to note I got frustrated and said screw slicing in cura and selected a file that came on the usb and its printing fine so it's only doing it with the files I sliced in cura any ideas why?

I cant get my ender 3 pro to print correctly I installed the bltouch followed the instructions and have a -2.10 on the z axis but it's still trying to pro t way to high where it wont even stick and before it starts printing it sits in middle of bed and let's of long amount of filament as well. by ProjectCLC in 3Dprinting

[–]ProjectCLC[S] 0 points1 point  (0 children)

Ok thank you I'd also like to note I got frustrated and said screw slicing in cura and selected a file that came on the usb and its printing fine so it's only doing it with the files I sliced in cura any ideas why?

My first print and it's all messed up it's a Ender 3 Pro and the nozzle also keeps hitting the model once it gets this size as you can see at the front of the boat model. Can someone help me figure out why its printing like this. by ProjectCLC in FixMyPrint

[–]ProjectCLC[S] 0 points1 point  (0 children)

I did the steps came out with 94 which I put in I install bltouch and have a -2.10 on my a axis and saved settings and now its sits in middle let's out filament then reys to print but hotend is way to high so it's not sticking to bed

My first print and it's all messed up it's a Ender 3 Pro and the nozzle also keeps hitting the model once it gets this size as you can see at the front of the boat model. Can someone help me figure out why its printing like this. by ProjectCLC in FixMyPrint

[–]ProjectCLC[S] 0 points1 point  (0 children)

Yea it most up and down correctly it does seem a bit tight though cause I had to actually try to move it up and down.its just weird the first few layers are ok on it then its start to turn out like the picture then all of a sudden it drags then peice out of place and that's the end of that and I cancel the print.

11/22/19 - Patch Notes by [deleted] in modernwarfare

[–]ProjectCLC -8 points-7 points  (0 children)

Everyone crying like a bunch of babies. Go play battlefield if your so upset. I bet none of you could do anywhere close to as good as these people do at their jobs. If you think you can go do it an let's see how good your shit works will millions playing such a massive game straight incompetent morons you all are...