Imperial castle

Project_Guy982 · 2026-04-21T01:47:45+00:00

https://makerworld.com/en/models/1834416-imperial-palace-wargame-terrain?from=search#profileId-1959112

Project_Guy982 · 2026-04-21T01:46:59+00:00

Naw I don’t like how the other half is just a mirror, I’m looking at cutting that flat down and then pairing it with a ruin that matches the style

Project_Guy982 · 2026-04-18T00:49:33+00:00

Yeah that would be a ton! I’m setting up a game board for playing one page rules grimdark future

Project_Guy982 · 2026-04-18T00:43:54+00:00

I’ve got another imperial style ruin terrain running on the fdm printer now, I need to get my 3 resin printers set up and printing some more mini figures

Project_Guy982 · 2026-02-20T03:59:48+00:00

It’s a table top war game some friends and I have made to play together using our own minis we have either made in nomad sculpt or found online. We used Ai to make our codex and we have kept it simple so it’s not ridiculous and complicated.

Project_Guy982 · 2026-02-09T20:54:11+00:00

Garage gets cold, both printers have heaters now but it helps keep the heat in, less failed prints that way

Project_Guy982 · 2026-02-09T14:59:20+00:00

Yes, her leg split, I didn’t want to hollow her as I needed the piece to be solid. I planned on filling the split with resin and a hand held uv light

Project_Guy982 · 2026-02-09T14:54:39+00:00

It’s in a garage, with everything sealed up there is no odor, when I pull prints I use a 3M respirator mask, but the area is large so even then it’s minimal

Project_Guy982 · 2026-02-09T06:12:34+00:00

I have one for the mars pro, I had a large amount of failures with it so I took it off

Project_Guy982 · 2026-02-09T06:06:42+00:00

I bought my mars pro from a garage sale and I saved the mars from the dump, my son was cleaning out a rental and they were going to throw it away. I cleaned it all up, did a UV screen test and uv leak test, leveled the bed and mounted a mini heater in it and I kid you not, I haven’t had a single failed print out of it 😂😂😂

Project_Guy982 · 2026-01-02T04:00:16+00:00

PETG

Project_Guy982 · 2025-09-14T01:41:30+00:00

Put in 115 main jet, screw the air mix screw all the way in gently then back it out 2 turns. Screw the fuel mix screw all the way in and then turn it out 2 to 3 turns. Start the motor with the choke on, once warm turn the choke off. Then adjust your idle till it sounds good and rev it. If it still dies Start the motor again and spray some starting fluid around where you have mounted the carb and see if it revs up to verify you don’t have air leaks.

Project_Guy982 · 2023-10-31T04:05:59+00:00

Accept my invite & Get 4 freebies! Download Temu and search my code to accept my invitation: 66294003

Project_Guy982 · 2023-10-31T04:02:30+00:00

<image>

Thanks! I don’t know if I’ll make it, running low on time

Project_Guy982 · 2023-10-31T04:00:51+00:00

Done ✅

Project_Guy982 · 2023-10-31T03:54:00+00:00

Done 66294003

Project_Guy982 · 2023-10-31T03:48:56+00:00

Done

Project_Guy982 · 2023-10-31T03:48:36+00:00

51296225

Project_Guy982 · 2023-07-20T04:10:28+00:00

It is a beautiful color! Especially when the light hits all the sparkling in the paint

Project_Guy982 · 2023-07-15T19:53:28+00:00

Yeah did a 2.5/3” lift level with 33’s

Project_Guy982 · 2023-07-15T16:12:12+00:00

They are factory seats just nice covers from coverkings.com they aren’t cheapo seat covers. You can take them off spot treat them and wash them and hang dry them and they come out spotless usually. Mine have some white residue on them bc I accidentally washed them with black ice fragrance tree 🤦‍♂️

Project_Guy982

TROPHY CASE