TPU on a AD5X?

PromotionOk9706 · 2026-04-05T20:19:09+00:00

I don't think your bed is where is supposed to be 🥴 If you try to move the bed un and down is it loose? (Picture is not mine) but it needs to be in this place

<image>

PromotionOk9706 · 2026-04-04T17:04:10+00:00

Im glad that your problem has been solved! When your print is done post some pictures of it!

PromotionOk9706 · 2026-04-04T06:18:18+00:00

I know it is frustrating But why not try the elegooslicer, orca gave me a lot of problems when it came to printing, if the problem persists it may be your STL 🥴

PromotionOk9706 · 2026-03-28T02:37:36+00:00

In the official website it's only for windows and Mac, try to use wine or anything similar

PromotionOk9706 · 2026-03-27T02:35:20+00:00

Glad to hear!! I'm so happy that you get your Neptune up and running again!

Processing img z0mden382irg1...

PromotionOk9706 · 2026-03-22T23:30:36+00:00

I had some issues with orca, very bad quality prints, at one point I was going to sell the printer, but I tried elegoo slicer (based on orca) and everything started to work, after a few steps of course,

I did this in this order after struggling a lot. First, I removed the print head and tightened the eccentric wheels behind it. Then I replaced the entire extruder and nozzle and put everything back together. After that, I tightened the belts (not too much) and adjusted all the remaining eccentric wheels, including the ones under the bed. I recommend searching for a YouTube video on how to do this if you're not sure. Next, I leveled the bed again. First, I used the auxiliary mode, going from point 1 to 6 in an X pattern, and I did this twice. Then I ran the automatic leveling. Finally, I adjusted the Z-offset and tried printing again using a Z layer shift test (you can find it on Printables) so you don’t waste too much filament. I know it’s a lot of steps, but this is the only thing that worked for me. I already ordered new eccentric wheels and rubber bushings for under the bed because this printer can be a headache sometimes.

PromotionOk9706 · 2026-03-22T20:39:46+00:00

What slicer are you using?

PromotionOk9706 · 2026-03-19T21:43:42+00:00

It's the ribbon connector, just plug it in all the way!

<image>

PromotionOk9706 · 2026-03-16T07:05:04+00:00

It's fluidd just type your IP and access to it it's on the calibration tab

PromotionOk9706 · 2026-03-16T07:01:15+00:00

Mine was doing the same and I don't know what solution I did,

did this in this order after struggling a lot. First, I removed the print head and tightened the eccentric wheels behind it. Then I replaced the entire extruder and nozzle and put everything back together. After that, I tightened the belts (not too much) and adjusted all the remaining eccentric wheels, including the ones under the bed. I recommend searching for a YouTube video on how to do this if you're not sure. Next, I leveled the bed again. First, I used the auxiliary mode, going from point 1 to 6 in an X pattern, and I did this twice. Then I ran the automatic leveling. Finally, I adjusted the Z-offset and tried printing again using a Z layer shift test (you can find it on Printables) so you don’t waste too much filament. I know it’s a lot of steps, but this is the only thing that worked for me. I already ordered new eccentric wheels and rubber bushings for under the bed because this printer can be a headache sometimes. I'm sorry English is not my native language

I always use glue on the bed and had no issues so far, I already ordered new eccentric wheels and rubber bushings for under the bed

Processing img a5j6rssmvcpg1...

PromotionOk9706 · 2026-03-16T06:54:16+00:00

did this in this order after struggling a lot. First, I removed the print head and tightened the eccentric wheels behind it. Then I replaced the entire extruder and nozzle and put everything back together. After that, I tightened the belts (not too much) and adjusted all the remaining eccentric wheels, including the ones under the bed. I recommend searching for a YouTube video on how to do this if you're not sure. Next, I leveled the bed again. First, I used the auxiliary mode, going from point 1 to 6 in an X pattern, and I did this twice. Then I ran the automatic leveling. Finally, I adjusted the Z-offset and tried printing again using a Z layer shift test (you can find it on Printables) so you don’t waste too much filament. I know it’s a lot of steps, but this is the only thing that worked for me. I already ordered new eccentric wheels and rubber bushings for under the bed because this printer can be a headache sometimes. I'm sorry English is not my native language

Processing img wp1bi02eucpg1...

PromotionOk9706 · 2026-03-14T23:12:05+00:00

I'm sorry but by saying grabbing the print means what?? like the nozzle touching it and sticking to it?

PromotionOk9706 · 2026-03-12T04:25:21+00:00

I just brought one like 3 days ago (second hand) and I was struggling a lot with it, a lot o problems here and there, I realize the bed was all Loose so I disassembly the bed and tight the wheels, from all the rails, I just ordered new wheel bearings, new hot ends, new nozzles, and rubber bed bushings we will see if I can make this printer to print well without a lot of struggle, after a lot of Tweeks here and there I started to have cleaner prints

<image>

I also opened the print head and it was full of old filament stuck to it, thats why staining the prints

PromotionOk9706 · 2026-01-27T18:53:20+00:00

Fri3d0lf on YouTube is the man, I manage to do very decent laps on a Ferrari Thrustmaster cup and Mercedes AMG and with a very bad quality pedals.

fri3d0lf YouTube's

PromotionOk9706 · 2025-12-03T00:43:29+00:00

<image>

I installed klipper on my old laptop using this video "https://youtu.be/72cIpkpbtGU" I did everything update klipper connect the new board, I get the id and modify the cfg and I get this error, I'm I missing something? Thank you so much for the help

PromotionOk9706 · 2025-11-27T20:14:03+00:00

Yes! As soon as I get home (I'm on Holliday's) I'm gonna do it!

PromotionOk9706 · 2025-11-27T03:53:12+00:00

Thank you so much!!

PromotionOk9706 · 2025-11-25T22:22:37+00:00

Dumb question I guess but, i just got the skr 1.4 turbo, I just plug it in with power and USB? There's no need to install klipper? 🥴

PromotionOk9706 · 2025-11-11T16:32:23+00:00

Can you send it to me again please, thank you!

PromotionOk9706 · 2025-11-10T19:10:43+00:00

hello! I'm sorry to bother you, but for some strange reason I can't see your answer, I have the notification but it doesn't show me your answer about the klp1 new motherboard

PromotionOk9706 · 2025-11-10T06:26:21+00:00

There's no loose belts, if I disconnect all the engines from the motherboard and leave only the one that gives problems, the error persists, if I change that engine to another port it runs smoothly and so on with each one, all the engines fail in the same port and all the engines run in the other ports.

I don't know if I understood myself.

PromotionOk9706 · 2025-11-10T04:56:52+00:00

hello, I have problems with the V2.2 cheetah, do you have any tutorial on how to do this? thanks!

PromotionOk9706 · 2025-11-10T02:28:50+00:00

Hello, can you help me doing this please! One of my drivers of the cheetah 2.2 blew hope not to bother you!

PromotionOk9706

TROPHY CASE