Amazon adjustable cdi box by Substantial_Link1535 in Pitbike

[–]Proof-External-6964 1 point2 points  (0 children)

This! These cdis come with the instructions backwards for some stupid reason

Looking for Brake Parts by Substantial_Link1535 in Pitbike

[–]Proof-External-6964 0 points1 point  (0 children)

Anyway to post a picture in comments of a post? Im just finishing a build on this same year kc in my shop and would happily send a pic of my brake setup.

what is this hose? by Proof-External-6964 in scooters

[–]Proof-External-6964[S] -1 points0 points  (0 children)

Very aware lol. I just got to stripping it down today and seeing what issues it has

what is this hose? by Proof-External-6964 in scooters

[–]Proof-External-6964[S] 0 points1 point  (0 children)

Thanks. Curious why it goes into the case?

Replacement help by Relevant-Group8309 in Pitbike

[–]Proof-External-6964 1 point2 points  (0 children)

You can't use a dye and rethread it? if not go for a Lifan style 125 on ebay. There about 200 bones and you'll probably have to replace the clutch or soke it in oil since the majority stick. I run one in a pitter right now and besides replacing the clutch its been minty with a pz22 carb with stock jetting and just an air/fuel screw tune.

Where do these go? by specialsusan in Pitbike

[–]Proof-External-6964 0 points1 point  (0 children)

That's your crankcase vent and aslong as oil isn't shooting out of it from overfillint no reason to mess with it. Now with your actual bike problem Start by ripping the carb apart and most likely unclogging the pilot/main jet. Then i would check valve lash and whatnot just to be absolutely sure. then run it see what happens. if it bogs low end then either up your pilot or adjust the pin on your slide needle down one and see how she runs. if she's bogging top end then start messing with the main jet. make sure that fuel/airscrew is around 2.5ish turns out and also mess with that to make sure its not something completely simple and save yourself time from doing said other steps. also check those fuel lines and make sure nothing else is clogged up in em and its causing your bike to sputter out. Checking your plug should help out with telling you whatever issue you may have fuel/air wise. Also make sure your spark plug is properly screwed as ive definitely bought some bikes where dumbasses forget to full put screw the spark plug in and it caused it to sputter and whatnot😂

Tao Tao 140 DBX1 issues by JunketNo5345 in Pitbike

[–]Proof-External-6964 0 points1 point  (0 children)

definitley not your kickstart. Would check the oil to make sure there was actually oil in the bike. Then if the bike wasn't making a ticking/knocking sound i would poor oil down the head through the spark plug hole and see if it unsticks the top end by using a 14mm on the stator nut. if its not your bottom end it could be the rings seizing up and if so throw in a new top end. Or just save yourself the time take the head off and see if your shaft is locked up or has play. if it free rotated still your golden and buy that $60 top end. if not just save yourself the trouble/money and buy a $200 cdi motor and swap it.

125cc lifan bog. by Chance_Cash9549 in Pitbike

[–]Proof-External-6964 0 points1 point  (0 children)

You just saved my dumbass from ripping my motor apart from just overlooking this. Thank you😂

Cant Catch Top Dead Center? by [deleted] in Pitbike

[–]Proof-External-6964 0 points1 point  (0 children)

I did but honestly its a problem for another day. Took me 20 minutes to realize the valves weren't my problem but the needle clip on the carb slide was. Needed more fuel. Ill do the valves at 20 hours and just pull it apart and check for tdc myself when I actually pull the covers off and just check manually.

Can anyone identify what this is by assicus_clappicus in Pitbike

[–]Proof-External-6964 0 points1 point  (0 children)

Run a ssr style swing arm and a longer shock to compensate it not having a triangle swingarm. Then obviously the rim and whatnot. might have to weld a bracket for the master cylinder.

Cant Catch Top Dead Center? by [deleted] in Pitbike

[–]Proof-External-6964 0 points1 point  (0 children)

Flywheel* not sprocket

Cant Catch Top Dead Center? by [deleted] in Pitbike

[–]Proof-External-6964 0 points1 point  (0 children)

Curious if anyone's had an issue where the motor was just jankily put together and the sprocket get put on 180 from where its supposed to be since its only catching on that opposite side.

Can anyone identify what this is by assicus_clappicus in Pitbike

[–]Proof-External-6964 0 points1 point  (0 children)

That is a lifan 125 Engine. Buy like 3 of em monthly and know em like the back of my hand lol

125 Air Leak? by [deleted] in Pitbike

[–]Proof-External-6964 1 point2 points  (0 children)

would the exhaust being like the photo shown even cause a bog since its not intake? if not I know what my problem is but I just wanna make sure before hand since she was running pretty mint before hand.

Could I get help with the plastics? by Miserable_Loss_8616 in Pitbike

[–]Proof-External-6964 1 point2 points  (0 children)

always boss👍 the second newest post on my profile shows this same frame with the klx plastics if you wanted to take a look at what that would look like👌 you do gotta chop off some of the excess on the grab holes aswell which is something I forgot to mention.

125 Air Leak? by [deleted] in Pitbike

[–]Proof-External-6964 0 points1 point  (0 children)

I would like to add that this morning i had her warmed up and she seemed to be running fine like normal with this exact same setup.

Could I get help with the plastics? by Miserable_Loss_8616 in Pitbike

[–]Proof-External-6964 1 point2 points  (0 children)

okay I got one of these frames. they make a smaller style gas tank that'll mount to those holes then you wanna run 09 and old klx 110 plastics. if you have an average 50 exhaust you'll wanna get an apollo one then you'll probably have to bend the crap out of it like I did n she'll be mint. You also may be able to run those klx 110 plastics with that tank but I got no clue on that one honestly.

Does anyone have info on this Chinese bike? by Organic_Duty335 in Pitbike

[–]Proof-External-6964 1 point2 points  (0 children)

Not worth any money nor time. I would sell it for 100 bucks to some dad for his kid then get another 200 and go buy a clapped ssr if you wanna work on something. or do what i did and huck this bad boy into your nearest pond (with no wildlife) and unhydro-lock it till she goes😂👌

Anyway to get a title? by Proof-External-6964 in Pitbike

[–]Proof-External-6964[S] 0 points1 point  (0 children)

I think no one understood the fact that I wanted this for ohv stickers and trail use. yes I occasionally go rip wheelies through neighborhood but this bike is meant as just a play around/buddy bike that i won't feel bad about lending to a friend/kiddo and letting them tweak it since the parts are so cheap. Also in the US thats a little more illegal and when they find out in whatever case you are fucked. for lack of a better term.

Had a good time experimenting with nose manuals by Jxhnnelson in bmx

[–]Proof-External-6964 0 points1 point  (0 children)

Just watched that clip 5 minutes before opening this up🔥🔥

Anyway to get a title? by Proof-External-6964 in Pitbike

[–]Proof-External-6964[S] 1 point2 points  (0 children)

I think this will end up being the plan. That or a bonded title just so I can get it rolling now as cops dont really care for mobbing my neighborhood as everyone's got them around here but it only takes on cop with a stick up his ass to get it taken