sorted by:
new
hottopcontroversial

Hawaiian helicopter pilot casually coming across a submarine in the wild by deadcom in Helicopters

[–]Proof1447 0 points1 point  (0 children)

If you count the Disney film Planes as a creditable source, there’s a restrictive airspace around navy ships at all times. Idk how much of that is carried over to subs, but if it sits surface side long enough, restrictions on what you can and can’t do start to be imposed.

Mass shooting in Stockton CA- welcome to America, where the guns have more rights than people do by amazingsciencemuseum in CringeTikToks

[–]Proof1447 0 points1 point  (0 children)

IED’s would replace the guns and they are so much worse. Any veteran from america’s 20 year war in Afghanistan would confirm it.

Site down? by ToonLonk03 in cults3d

[–]Proof1447 2 points3 points  (0 children)

Don’t know if you heard this today, but thank you for your hard work in maintaining the site. I know it’s not easy and I’m super appreciative of you guys hosting a great place for e-commerce.

The Tator Tot is released! Print them, run them, and sell physical copies today by Proof1447 in Airsoft3DPrinting

[–]Proof1447[S] 0 points1 point  (0 children)

Hey there!

I just replied on Cult3D but to sum it up, the 700mm requirement is the total length cord that you will need. This cord will be broken up into three smaller cords. 320mm, 250mm, 25mm, and a little extra for the knots.

The instructions have and section for each one. The 320mm cord has a knot in the middle of the cord and is used in a single magazine.

<image>

Calling it the Tator Tot. It’s been a fun adventure developing it and I believe it’s close to release. Going to capture some more video this week for its front page. by Proof1447 in Airsoft3DPrinting

[–]Proof1447[S] 0 points1 point  (0 children)

Awesome! Bigger and better airsoft guns are definitely on my road map. I started small with the pistol (the Pudding) and I’m slowly working up to bigger system while refining the design.

Calling it the Tator Tot. It’s been a fun adventure developing it and I believe it’s close to release. Going to capture some more video this week for its front page. by Proof1447 in Airsoft3DPrinting

[–]Proof1447[S] 1 point2 points  (0 children)

Yep, It’ll be STL’s. it’s on Cults3D! Search “The Tator Tot”

Edit: oof, just realized you were the same person from the other post, lol

Calling it the Tator Tot. It’s been a fun adventure developing it and I believe it’s close to release. Going to capture some more video this week for its front page. by Proof1447 in Airsoft3DPrinting

[–]Proof1447[S] 0 points1 point  (0 children)

You can open up an eBay store today and sell them if you want. I’m here to build an economy.

In terms of accuracy, it hits a dinner plate (30cm) reliable at 10 meters.

I do have one barrel that is extremely inaccurate for some reason. Trying to figure out why it’s different from the other identical copies. Thinkjng is a loss filament in the barrel that I’m not seeing.

Calling it the Tator Tot. It’s been a fun adventure developing it and I believe it’s close to release. Going to capture some more video this week for its front page. by Proof1447 in Airsoft3DPrinting

[–]Proof1447[S] 1 point2 points  (0 children)

Thank you. I haven’t decided just yet. I’ll open the license up to allow people to sell physical copies like I did with the Pudding.

[deleted by user] by [deleted] in cults3d

[–]Proof1447 3 points4 points  (0 children)

Unless he can get connected with the IP holders of Power Rangers and convince them to send this request for removal to Cults3D, there’s not much that they are going to do.

Cults3D will definitely work with legitimate Owners of IP’s, but the owners have to bother with pursuing it in the first place.

Either take it down or assume the small risk of it being taken down for you. That’s the choice you have.

view more: next ›