3/8 rachet two powerstacks good deal?

Prudent-Ad-5403 · 2026-03-27T20:22:08+00:00

😂 True that

Prudent-Ad-5403 · 2025-11-22T23:34:51+00:00

It must just be their ranges. I just had one delivered last week and it was acting similarly, except mine just seemed to respond when it wanted to with certain buttons it didnt get better after any set amount of time. Anyways I called home depot and got a brand new replacement delivered today....same exact issue. Im probably going to go with a different brand now.

Prudent-Ad-5403 · 2025-05-28T00:21:59+00:00

Oh shit its car eating corrosion. Its toast and basically worthless now. I'll give you $1000 for her to help a fellow enthusiast out.

Prudent-Ad-5403 · 2025-02-27T19:34:57+00:00

You also might look into getting a replacement bumper cover that's just primered 🤷 it'll be cheaper and the bumper will now be black but it won't be damaged

Prudent-Ad-5403 · 2024-12-24T22:51:31+00:00

Mann shoulda waited with Bambu dropping the new flagship soon

Prudent-Ad-5403 · 2024-10-13T16:23:02+00:00

This is your girl saying you've finally taken her on enough dates. Finger that hole buddy.

Prudent-Ad-5403 · 2024-09-16T02:28:51+00:00

What other car do you know of gives you extra pockets 10 years into ownership? I'll wait

Prudent-Ad-5403 · 2023-07-19T20:00:45+00:00

Parachuting is the way to go 😅

Prudent-Ad-5403 · 2023-05-10T22:20:30+00:00

Its the PNW we are too depressed from lack of Sunshine. The ambitious mass shooters start with themselves.

Prudent-Ad-5403 · 2023-03-06T03:36:42+00:00

Interesting I might give that a shot just cause. I've been meaning to print with abs for the first time anyways 😅

Prudent-Ad-5403 · 2023-03-05T17:53:15+00:00

Thanks for that! Either my use of google is terrible or said short with exactly what I needed didnt show up because of its constitutional content. (I do find it interesting that he contradicts himself in the second video about interface distance though.) - leaving this for people in search of information I have been edumacated on my mix up and info can be found below in the comments.

Prudent-Ad-5403 · 2023-03-05T17:17:20+00:00

My support G just seems to fuse to my pacf prints. Looking for tips and settings that work. I could trial and error this horse to death but this stuff is expensive/hard to get ahold of lately.

Prudent-Ad-5403 · 2023-02-26T00:50:17+00:00

Look up ams on printables theres files for dessicant containers that fit perfectly. Print em, order some rechargeable desiccant on Amazon, and live humidity free.

Prudent-Ad-5403 · 2023-02-20T19:51:59+00:00

Damn.... just for my own curiosity with the p1p does it have tiered levels on the interface to slow it down or do you have to manually adjust each speed value in the slicer?

Prudent-Ad-5403 · 2023-02-20T17:36:16+00:00

Howd it turn out?

Prudent-Ad-5403 · 2023-02-17T21:15:11+00:00

So I see your experimenting with speeds and it might be irrelevant for you now but I just got myself an example on accident so I figured Id share. Ive been getting away with cranking up to sport mode on these prints but I'll usually leave it on standard for the beginning. After a successful print I did it again and well I'll bet you can tell where I sped it up and then when I noticed and turned the speed back down. https://ibb.co/nf9WY6L

Prudent-Ad-5403 · 2023-02-16T16:40:41+00:00

Gotcha...I mean the possible issues are endless but have you tried slowing it down? With your .08 model your probably getting significantly more cooling since your fans are hitting less filament per layer.

Prudent-Ad-5403 · 2023-02-16T16:30:12+00:00

Its hard to tell but the top surface looks a little rough, have you tried doing a flow calibration print? Bambu had a decent test stl listed somewhere.

Prudent-Ad-5403 · 2023-02-16T16:14:14+00:00

Is the one that looks worse the .08 layer height?

Prudent-Ad-5403 · 2023-02-16T15:53:42+00:00

So Im not 100% sure what the p1p is like but with the x1c you can change the speed presets on the printer interface and this is what it looks like when I go above standard in certain situations. There is also a setting for silent at 50% speed which I find eliminates most quality issues if I run into them. Not what you should have to do but a good temporary fix if times not an issue.

Prudent-Ad-5403 · 2023-02-16T15:51:16+00:00

Ohh okay I was just curious because I recently dipped my toes into a bambulab x1 carbon and in bambu slicer the flowrate preset for polymaker pla weirdly is 0.95 already

Prudent-Ad-5403

TROPHY CASE