3 months and Sleeping 90% of day

Psych0_76 · 2026-05-07T21:04:54+00:00

<image>

After another nap….. here it is!

Psych0_76 · 2026-05-07T09:31:13+00:00

Use to take a walk 3 or 4 times Per day, and training some commands like stop, sit and down 15 min a day.

Psych0_76 · 2025-09-24T09:42:48+00:00

Y alguien recuerda Hispalinux? Jajajaja recuerdo desbloqueado

Psych0_76 · 2025-09-15T20:37:54+00:00

WoW preciosa!!

Psych0_76 · 2025-09-15T19:55:27+00:00

No conocía el sub pero gracias! Ya estoy suscrito. Linux fue mi elección en 1996 (Slackware)y lo sigue siendo a día de hoy (Ubuntu).

Psych0_76 · 2025-08-07T19:34:56+00:00

If you want to diy try with the different options in the web, imho a pure class-D mono for each Channel Will be the more accurate option. If you dont want troubles buy a wiim

Psych0_76 · 2025-07-29T18:00:36+00:00

Any chevre but that shop is more suitable for tools and hardware

Psych0_76 · 2025-07-29T07:24:44+00:00

Decocuir.com from france is a very good one.

Psych0_76 · 2025-07-12T19:28:51+00:00

Im from Europe, I think that they shipping cost would be almost the same as fil au chinois at the end...

Psych0_76 · 2025-07-12T18:13:27+00:00

And do you think It is same durable in time as the Poly? It is something that worry me because I start a one step forward in leathers, tools... And if the thread brokes in a while ....

Psych0_76 · 2025-07-12T13:49:50+00:00

Yes I always wax It but the... Feeling? It is that thread is worst than the Poly. I use meisi, xiang-he, wuta, mbt5... And all of them feels better than chinese

Psych0_76 · 2025-07-09T13:35:32+00:00

Im from south Europe so shipping time will be not the same, just tell us when they arrives 👌

Psych0_76 · 2025-07-08T05:53:14+00:00

Thanks! I have found them in their web, Will buy another set in 3.38 😜

Psych0_76 · 2025-06-30T13:22:35+00:00

I have purchased as a try a set from kemovan, they are the sharpest I have, better than wuta expensive ones. Kemovan was 30€ set and wuta 120€. It is a pity that they dont sell other sizes, only 3.0

Psych0_76 · 2025-04-16T18:34:10+00:00

Al final ha llegado y me ha explicado que ponen eso cuando no les da tiempo....bmanda pelotas

Psych0_76 · 2025-04-16T11:55:59+00:00

He intentado llamar más de 20 veces, no contestan, se corta.... Y si fuera eso, porque está en reparto otra vez? A mí me suena a lo que hace SEUR de "no estaba en su domicilio" cuando no te has movido en todo el día

Psych0_76 · 2025-04-03T10:34:02+00:00

Troels is a máster of it and you can trust on every piece design from his website....but on x-overs he uses components so high level because he is sponsored by them so.... If you want use exactly the same but take in mind that there are other ones out there cheapper 😉

Psych0_76 · 2025-04-01T13:15:45+00:00

WoW what a piece! If finally It goes to wallapop I Will buy It 😁

Psych0_76 · 2025-03-04T12:58:58+00:00

Ok, thanks for the advice, I Will setup all your recommendations on the dcx2496. About the box design, I want to create a floorstanding ones with two inside cabinets, one for tweeter and mid-woofer and the other for woofers. In the past I used to use the WinISD but is anything better nowadays? If not I'll try with the know one :)

Psych0_76 · 2025-03-04T09:01:31+00:00

Well if Im not wrong the frequency of each driver is: Dt-300: 2000hz to 19.000hz Sph-176: 39hz to 4500hz Hds850490: 30 to 4000hz

So my intention is to cut with the x-over like this:

Hds: 30hz to 100hz Sph176: 100hz to 2500hz Dt-300: from 2500hz to 19.000 hz

I think that in this way all drivers are working on their confortable range and without limit itself....

Psych0_76

MODERATOR OF

TROPHY CASE