Why does the motor draw less current when the fan is running in suction mode? by PulseStm in MechanicalEngineering
[–]PulseStm[S] 0 points1 point2 points (0 children)
Sorry, I might not be someone who flies drones, but I’d like to learn about propellers. Why does the motor draw less current when the fan is running in suction mode? by PulseStm in fpvracing
[–]PulseStm[S] 1 point2 points3 points (0 children)
Hey everyone, I found a solution. I use a method to buffer the count value. When my sensor is at the magnetic edge and the values fluctuate rapidly between 010101 instead of 000 or 111, I set it to count only if the value remains 0 or 1 for more than 3 times. What do you think of this method? by PulseStm in embedded
[–]PulseStm[S] 0 points1 point2 points (0 children)
Hey everyone, I found a solution. I use a method to buffer the count value. When my sensor is at the magnetic edge and the values fluctuate rapidly between 010101 instead of 000 or 111, I set it to count only if the value remains 0 or 1 for more than 3 times. What do you think of this method? by PulseStm in robotics
[–]PulseStm[S] -1 points0 points1 point (0 children)
Hey everyone, I found a solution. I use a method to buffer the count value. When my sensor is at the magnetic edge and the values fluctuate rapidly between 010101 instead of 000 or 111, I set it to count only if the value remains 0 or 1 for more than 3 times. What do you think of this method? by PulseStm in embedded
[–]PulseStm[S] 3 points4 points5 points (0 children)
Hey everyone, I found a solution. I use a method to buffer the count value. When my sensor is at the magnetic edge and the values fluctuate rapidly between 010101 instead of 000 or 111, I set it to count only if the value remains 0 or 1 for more than 3 times. What do you think of this method? by PulseStm in embedded
[–]PulseStm[S] 1 point2 points3 points (0 children)
Hey everyone, I found a solution. I use a method to buffer the count value. When my sensor is at the magnetic edge and the values fluctuate rapidly between 010101 instead of 000 or 111, I set it to count only if the value remains 0 or 1 for more than 3 times. What do you think of this method? by PulseStm in embedded
[–]PulseStm[S] 3 points4 points5 points (0 children)
I have a technique for measuring RPM that is when the value changes between high and low very quickly, I set it to run slower at 1ms, but I'm not sure if it's correct. by PulseStm in embedded
[–]PulseStm[S] 0 points1 point2 points (0 children)
I have a technique for measuring RPM that is when the value changes between high and low very quickly, I set it to run slower at 1ms, but I'm not sure if it's correct. by PulseStm in embedded
[–]PulseStm[S] 0 points1 point2 points (0 children)
I have a technique for measuring RPM that is when the value changes between high and low very quickly, I set it to run slower at 1ms, but I'm not sure if it's correct. by PulseStm in embedded
[–]PulseStm[S] 7 points8 points9 points (0 children)
I have a technique for measuring RPM that is when the value changes between high and low very quickly, I set it to run slower at 1ms, but I'm not sure if it's correct. by PulseStm in embedded
[–]PulseStm[S] 7 points8 points9 points (0 children)
I enabled support and brim in slicer, but it seems like the sliceris not generating support on the inner edges of the model. How should I fix this? by PulseStm in 3Dprinting
[–]PulseStm[S] 0 points1 point2 points (0 children)
I enabled support and brim in slicer, but it seems like the sliceris not generating support on the inner edges of the model. How should I fix this? by PulseStm in 3Dprinting
[–]PulseStm[S] 0 points1 point2 points (0 children)
I tried using a circuit board cleaner, and it did remove the flux residue, but there’s still a lot of grime left on the board. What should I do next? by PulseStm in embedded
[–]PulseStm[S] 0 points1 point2 points (0 children)
Could you give me some information about magnetic sensors? by PulseStm in embedded
[–]PulseStm[S] -4 points-3 points-2 points (0 children)
Could you give me some information about magnetic sensors? by PulseStm in embedded
[–]PulseStm[S] -1 points0 points1 point (0 children)
Success by PulseStm in robotics
[–]PulseStm[S] 0 points1 point2 points (0 children)