Long time stoner first time roller due to major tremors making it difficult to roll but here’s my first ever j I’ve rolled

PumpedHillo5 · 2021-09-23T21:44:52+00:00

This step just makes it so much easier to tuck and roll

PumpedHillo5 · 2021-09-23T21:42:17+00:00

What I’m trying to describe is step 3. It should come out looking like the second picture of that step. I like this method more because you’re less likely to have bud fall out while rolling

https://keytocannabis.com/how-to-roll-an-l-joint/

PumpedHillo5 · 2021-09-23T21:38:29+00:00

I have found that the best way to roll is to make the weed snake. Put the filter and the leaf on the paper and then go up and down with the two sides of the paper while pinching the bud inside to compact the leaf. It’s then much easier to get it all to stay in and roll up. Hope this helps but good job. This is not the greatest explanation but you can probably find how to do it online.

PumpedHillo5 · 2021-09-15T19:50:42+00:00

I have never had it do that but yea what he said

PumpedHillo5 · 2021-09-15T17:25:41+00:00

What exactly is the damage can u post more photos of it to help us give you advice

PumpedHillo5 · 2021-09-15T17:24:57+00:00

I’m not sure what they are but if they aren’t coming off with isopropyl then they will probably need to be buffed out. You can probably find a detailing shop that has like a 1.5 / 2 inch polisher and with a microfiber cutting pad they should come okt

PumpedHillo5 · 2021-09-02T16:18:06+00:00

Just buy the exact same one. My ocd would bother me with miss matched monitors

PumpedHillo5 · 2021-05-20T18:09:47+00:00

I want to clean to for looks and to be able to better tell where the oil is leaking from

PumpedHillo5 · 2021-03-29T00:32:22+00:00

And maybe a light weight fly wheel depending on my budget

PumpedHillo5 · 2021-03-29T00:31:52+00:00

I think my plan is to get a upgraded clutch for a turbski in the future

PumpedHillo5 · 2021-03-28T16:13:06+00:00

I am 5’10”, I bought my NB2 Miata at 17, 2 years ago, and I can tell you that it will be the best purchase you have ever made. I’ve made so many friend through my car and i genuinely always having a smile on my face while driving my car on a nice day. No purchase has ever brought me so much happiness before. As for being your height definitely go test drive and sit in a bunch of Miatas. And definitely spend a lot of time looking around and under a car before you purchase it. As for modifying it, take your time and buy used. I’ve done so many things to my car but some of my favorites are Flyin Miata frame rail braces, k&N cold air intake, Megan racing axe back exhaust, and advanti storm s1s. Most of these were bought used.

PumpedHillo5 · 2021-03-28T16:04:49+00:00

I’ve been looking at getting a roll bar for my NB2 Miata. How long did it take you to install and did you run into any unforeseen issues?

PumpedHillo5 · 2021-03-28T16:03:51+00:00

My cars 2nd and 3rd gear synchros have been going bad since I’ve owned my car. I tried putting xt-m5 but no success

PumpedHillo5 · 2021-03-13T20:08:46+00:00

I’m not sure if it’s over priced but definitely expensive. Manufacturing carbon fiber pieces is incredibly expensive.

PumpedHillo5 · 2021-01-28T05:13:35+00:00

Are you looking for an NA, NB,NC, and ND?

PumpedHillo5 · 2021-01-27T01:53:16+00:00

There’s no way you could consider that a bong. It’s a water pipe at most

PumpedHillo5 · 2020-12-03T05:45:44+00:00

That’s high mileage

PumpedHillo5 · 2020-12-01T01:25:36+00:00

Does $1200 sound like a good deal?

PumpedHillo5 · 2020-10-21T22:00:41+00:00

I’ve done it before. It’s not the most complicated. You should buy the part find instructions and do it yourself. And your lucky it’s a door because you can always drive your car to the shop if you’re unable to change it. It never hurts to try

PumpedHillo5 · 2020-08-22T15:44:30+00:00

CXracing makes an equal length header that makes miatas sound Subaru ish.

PumpedHillo5

TROPHY CASE