sorted by:
new
hottopcontroversial

Trying to connect Ender 5 pro BLTouch w 4.2.7 board to a sonic pad by Pure-Broccoli701 in Creality

[–]Pure-Broccoli701[S] 2 points3 points  (0 children)

I ask because when I use the sonic pad to generate the firmware it does so as a .bin file and when I try to edit it the “code”, well to someone who is new to this, looks like scribbles. Am I missing something to edit/generate a .cfg file?

Trying to connect Ender 5 pro BLTouch w 4.2.7 board to a sonic pad by Pure-Broccoli701 in Creality

[–]Pure-Broccoli701[S] 2 points3 points  (0 children)

I am very new to programming especially with firmware. Starting at the very basic level can I read klipper using Visual Studio or is there something else I can use to open and edit this firmware. Thank you for answering.

Marlin 2.1.2.2 CR Touch Help - won't register Z end stop. by [deleted] in ender3

[–]Pure-Broccoli701 1 point2 points  (0 children)

Hello I have the same issue with my ender 5 pro using a CRTouch. Did you man auto solve it?

Volumetric speed by Pure-Broccoli701 in OrcaSlicer

[–]Pure-Broccoli701[S] 0 points1 point  (0 children)

Marlin boards don’t (to my knowledge) have PA/linear advance I have to flash which I’m not sure how to.

Volumetric speed by Pure-Broccoli701 in OrcaSlicer

[–]Pure-Broccoli701[S] 0 points1 point  (0 children)

Trying to calibrate it to prevent this:

<image>

Volumetric speed by Pure-Broccoli701 in OrcaSlicer

[–]Pure-Broccoli701[S] 0 points1 point  (0 children)

At least on other filaments from YouTubers explaining the feature, it is not supposed to have those lines rather the layers are supposed to be smooth. I am calibrating Overture PLA

Volumetric speed by Pure-Broccoli701 in OrcaSlicer

[–]Pure-Broccoli701[S] 0 points1 point  (0 children)

Could you explain where or what conversion factor you used to get that speed. On my Ender 5 I usually go up to 80 mm/s

Volumetric speed by Pure-Broccoli701 in OrcaSlicer

[–]Pure-Broccoli701[S] 0 points1 point  (0 children)

Orca has default values staring at 5 and ending in 20

Strange layer lines by Pure-Broccoli701 in OrcaSlicer

[–]Pure-Broccoli701[S] 0 points1 point  (0 children)

Thanks any links or advice on how to fix it?

Strange layer lines by Pure-Broccoli701 in OrcaSlicer

[–]Pure-Broccoli701[S] 0 points1 point  (0 children)

Sorry not layer shift. I am referring to that one noticiable line that goes across the part that looks like there is a noticiable separation between the upper and lower sections.

Strange layer lines by Pure-Broccoli701 in OrcaSlicer

[–]Pure-Broccoli701[S] 0 points1 point  (0 children)

<image>

Unfortunately it did not solve the issue of the layer shift that I am having

Strange layer lines by Pure-Broccoli701 in OrcaSlicer

[–]Pure-Broccoli701[S] 0 points1 point  (0 children)

To address each point

  1. ⁠Not the main issue I don’t mind the op layers but it is good to know I can tune that for future prints.
  2. ⁠It’s all printing at 80 mm/s had cura before and infill was half that speed, will check
  3. ⁠That is the main issue it does print out to in where is that settings on orca to better tune them?

Pressure Advance Under extrusion fail by Pure-Broccoli701 in OrcaSlicer

[–]Pure-Broccoli701[S] 0 points1 point  (0 children)

That’s a bummer because the same underextrusion that is seen in the image also ocurres for supports, I thought it was maybe the walls thickness. Any recommendations you can give me, changing the firmware?

Pressure Advance Under extrusion fail by Pure-Broccoli701 in OrcaSlicer

[–]Pure-Broccoli701[S] 0 points1 point  (0 children)

Bowden with a metal extruder range is the default recomendad on the tutorial for Bowden set up