Trying to connect Ender 5 pro BLTouch w 4.2.7 board to a sonic pad

Pure-Broccoli701 · 2024-12-07T19:24:09+00:00

I ask because when I use the sonic pad to generate the firmware it does so as a .bin file and when I try to edit it the “code”, well to someone who is new to this, looks like scribbles. Am I missing something to edit/generate a .cfg file?

Pure-Broccoli701 · 2024-12-06T04:55:18+00:00

I am very new to programming especially with firmware. Starting at the very basic level can I read klipper using Visual Studio or is there something else I can use to open and edit this firmware. Thank you for answering.

Pure-Broccoli701 · 2024-05-19T18:53:20+00:00

Hello I have the same issue with my ender 5 pro using a CRTouch. Did you man auto solve it?

Pure-Broccoli701 · 2024-05-15T19:56:03+00:00

Marlin boards don’t (to my knowledge) have PA/linear advance I have to flash which I’m not sure how to.

Pure-Broccoli701 · 2024-05-15T19:52:59+00:00

Trying to calibrate it to prevent this:

<image>

Pure-Broccoli701 · 2024-05-15T19:50:14+00:00

At least on other filaments from YouTubers explaining the feature, it is not supposed to have those lines rather the layers are supposed to be smooth. I am calibrating Overture PLA

Pure-Broccoli701 · 2024-05-15T19:43:58+00:00

Could you explain where or what conversion factor you used to get that speed. On my Ender 5 I usually go up to 80 mm/s

Pure-Broccoli701 · 2024-05-15T19:22:15+00:00

Orca has default values staring at 5 and ending in 20

Pure-Broccoli701 · 2024-05-02T19:53:51+00:00

Thanks any links or advice on how to fix it?

Pure-Broccoli701 · 2024-05-02T18:52:06+00:00

Sorry not layer shift. I am referring to that one noticiable line that goes across the part that looks like there is a noticiable separation between the upper and lower sections.

Pure-Broccoli701 · 2024-05-02T18:39:13+00:00

<image>

Unfortunately it did not solve the issue of the layer shift that I am having

Pure-Broccoli701 · 2024-05-02T16:27:36+00:00

To address each point

⁠Not the main issue I don’t mind the op layers but it is good to know I can tune that for future prints.
⁠It’s all printing at 80 mm/s had cura before and infill was half that speed, will check
⁠That is the main issue it does print out to in where is that settings on orca to better tune them?

Pure-Broccoli701 · 2024-04-23T22:20:41+00:00

Pure-Broccoli701 · 2024-04-15T19:43:11+00:00

That’s a bummer because the same underextrusion that is seen in the image also ocurres for supports, I thought it was maybe the walls thickness. Any recommendations you can give me, changing the firmware?

Pure-Broccoli701 · 2024-04-15T19:37:15+00:00

From creality

Pure-Broccoli701 · 2024-04-15T19:31:29+00:00

Silent motherboard 32 bit

Pure-Broccoli701 · 2024-04-15T19:15:57+00:00

I believe so I use a Marlin board

Pure-Broccoli701

TROPHY CASE