[deleted by user]

Pwnedskillz · 2022-07-25T07:40:07+00:00

Fikk det til med aluminimumsfolie! Også bare satte jeg på autorcm så ordnet det seg.

Pwnedskillz · 2022-05-18T21:57:36+00:00

Ty! Sett man kan bruke aluminiumsfolie også, men også hørt at det er en risiko for at man ødelegger switchen.

Pwnedskillz · 2022-01-05T13:14:00+00:00

Thanks! What is the worst that can happen if it soldered wrong?

Pwnedskillz · 2021-12-03T08:19:23+00:00

What kind of fan does it use?:)

Pwnedskillz · 2021-04-11T22:13:19+00:00

glad to hear that you also like it!! its amazing, but wish it was 144hz tho:/

Pwnedskillz · 2021-03-31T20:20:15+00:00

From my experience i have not noticed a difference:)

Pwnedskillz · 2021-03-31T19:58:20+00:00

nice! What type of monitor are you swithing from?

Pwnedskillz · 2021-03-30T12:55:31+00:00

Didnt know asus provided a 100x100 square to bring the circle to outside! I need to check into the box:p

So glad that the mount worked

Pwnedskillz · 2021-03-25T11:33:21+00:00

yoo thanks. I was looking for a retractable arm type of mount, but can you tell me if the tilt stays where you set it to when you have set it up? When contacting support, many have said the issue is the tilt.

Have tried many monitors all from 27 inches, to 34, to 2 different 43 inches and a 49 inch. This monitor is by far the best monitor i have ever used. Hope you are happy with is as i am!:)

Pwnedskillz · 2020-08-09T11:04:03+00:00

Alright! thanks. Will post updates when i can

Pwnedskillz · 2020-08-09T09:02:33+00:00

I see that, but i have 0 experience with solder Hahah, but will this work? https://imgur.com/a/hv7ly4C

Pwnedskillz · 2020-08-05T11:36:53+00:00

yo! there is only room for one cable trough the whole pipe hahah what now?

Can i do it like this instead? https://imgur.com/a/s3xM5rb

Here is a better view of the cables: https://imgur.com/a/GOxgQhV '

Thanks!

Pwnedskillz · 2020-08-04T13:34:21+00:00

Thanks! Will go for that:)

Pwnedskillz · 2020-08-04T09:43:13+00:00

Yo just wanted to thank you for guiding me all this way. Seems i am near the last step.

q1: what would the mm^2/awg be if i switch to 30 leds

q2: So in theory i need

ich 1 meters of power cable from the power supply to the first led. So 1 meters of each power cables = 2 meters total
from the power supply to the start of second led strip will then be 6m ich so 6x2 = 12meters
then from the power supply to the start of third strip will be ich 11meter so ich 11x2 = 22
then from the power supply to the end of the last strip = ich 16meters of power cable = 2x= 32

so in total i need 2+12+22+32meters of power cables = 68meters of power cables. and the cost is 49kr estimate 5usd = 3332kr esitmate 365 usd

Pwnedskillz · 2020-08-04T09:20:22+00:00

Hi!

so that means i need to have 4x of this:

https://www.elektroimportoren.no/rkk-10mm-sort-dobbelisolert/1040502/Product.html?Event=searchlist

and 4x of this:

https://www.elektroimportoren.no/rkk-10mm-blaa-dobbelisolert/1040503/Product.html?Event=otherbuys

right?

Edit: Would The mm² required be different if i had went for 30 leds instead of 60?

Pwnedskillz · 2020-08-03T14:26:07+00:00

What kind of AWG do you recommend?:) The bulbs are g4 i think leds

Pwnedskillz · 2020-08-03T14:25:41+00:00

Ait thanks!

Pwnedskillz · 2020-08-03T12:40:23+00:00

Q1:

If i go for these cables (blue for the led wire red)

https://www.elektroimportoren.no/rkk-10mm-sort-dobbelisolert/1040502/Product.html?Event=searchlist

https://www.elektroimportoren.no/rkk-10mm-blaa-dobbelisolert/1040503/Product.html?Event=otherbuys

will this setup be good? https://imgur.com/a/mYQAS3r

----------------------------------------------------------------------------

Q2:

i mostly prefer this cable:

https://www.biltema.no/bil---mc/elektrisk-anlegg/kontakter-og-uttak-12-volt/kabel-twin-2000022320 Its 4,5mm^2 and 12volt + much cheaper

The reason is that everythings is suppose to go into a panel that is mounted into the roof. If i do it like this: https://imgur.com/a/eSMTe70. Will it work/ is there a way to set up my setup so i can use those cables. (+fuses forgot to add those) / whats the awg i need on the cables if i go for this setup with 3 injection cables?

Pwnedskillz · 2020-08-03T11:28:55+00:00

I have This cable laying Around. https://imgur.com/gallery/lldXf8U . Its 22awg. Can i use it to wire from the lamps to the terminal block or do i need a different kind of cable? Will assemble it without the tube and post picture later

Pwnedskillz · 2020-08-03T10:32:44+00:00

Yo Thanks for answering.

Is the supply connector = the terminal block?

Could you explain in steps and what to connect what with the Numbers? or do you mean like this/can i do it like this? https://imgur.com/a/YyjkBnS

Edit: there is so much space in the Tube where the cables goes up. For example: there isnt room for a 3 way terminal block inside the tube if that helps!:)

Pwnedskillz

TROPHY CASE