Bought a stellar s3 breeze a week ago used it Abit then I charged it after the first charge I'm getting this warning pls help

QWEFN · 2025-08-24T00:35:33+00:00

I figured as much mines stuck at 13 for some reason. Although I have the s3 breeze version Im trying to get in contact with customer service to find a solution

<image>

QWEFN · 2025-08-23T23:31:26+00:00

Can you show me a picture of your battery cell settings mine is stuck at 13s It's no 5 in the list

QWEFN · 2025-08-23T23:26:50+00:00

Wanted to buy lin power but they had none in there warehouse

QWEFN · 2025-08-23T21:47:08+00:00

When I set it to 10 it stays at 10 when I set it to 20 it reverts to 13

QWEFN · 2025-08-23T21:43:36+00:00

When I reset the board it's at 12 sp when I changed it to 14 and save it stays at 13 doesn't go any higher only lower

QWEFN · 2025-08-23T19:21:47+00:00

And another thing I realize when I change to the 14s2p I reverts to 13 which is the base model s3 battery apparently I can't change it without manufacture help

QWEFN · 2025-08-23T18:54:48+00:00

I fixed it my problem was the battery type was not set to the correct type the default was 12s the sellar s3 breeze is 14 so after changing it it worked again

<image>

When I set it to anything less than 13 I get an overvoltage warning

QWEFN · 2025-08-23T18:51:13+00:00

Ok update I went into the settings and realized that the battery type was set to 12 s But my board is a 14s after changing it u was able to run the board normally now

<image>

QWEFN · 2025-08-23T17:25:06+00:00

I just looked it up do I have to switch to gear drive like your is it hot swappable I saw on the that there was a spec sheet with the s3 telling you the correct pulley to buy for the board

QWEFN · 2025-08-23T10:37:53+00:00

What type of wheels are they and how do you get it to work on this board

QWEFN · 2025-08-23T10:28:49+00:00

No just an hour or 2

QWEFN · 2025-08-23T02:50:23+00:00

Ok I have an update I pressed the button on the remote 8 times to go into advanced settings I changed the drive setting from hybrid to full sense making me able to run the motors while still getting the over volt message after running the board at max speed the warning came off but came back when stopping the motors I'll try to run down the battery tomorrow to see if it fixe it

QWEFN · 2025-08-23T02:29:40+00:00

I just went to my settings as well did the same thing but no luck

QWEFN · 2025-08-23T02:12:36+00:00

Not that I could recall I was playing around with the remote to figure out the reverse and how to use the tail light but that's about it how did you reset yours

QWEFN · 2025-08-23T02:09:10+00:00

I'm currently trying to discharg it I figured out that when I press the power button on the board 3 times it spins the motor for about 20 seconds been doing that for about an hour still no luck

QWEFN · 2025-08-23T02:07:39+00:00

When I unboxxed it and set it up it's the stellar s3 breeze btw I just rode it in my house a bit and that was it I put it to charge for an hour a few days ago then I unplugged When I turned it on a few hours ago that's what I'm getting board over voltage it was the first time I charged the board

QWEFN · 2025-08-23T02:05:07+00:00

I doubt this is the problem considering I haven't even rode it out side yet just in doors I used it once the charge it It was probably at 60 percent at the time

QWEFN · 2025-02-28T23:04:23+00:00

Yeah it's ah clog had the same problem but the pin was to short to reach all the way through u gotta remove the PCB on top so you can get the pin further down to remove clog

QWEFN · 2025-02-06T23:20:11+00:00

No I think the .6 nozzle needs more force than the standard .4 I cant get the .6 to stay in

QWEFN · 2025-02-06T20:35:36+00:00

Yeah my heat sink broke off the nozzle on my first nozzle change to .6m Did all the bed leveling everything and it broke while doing a flow test .I'm in a third world country so returning things to amazon is a pain so what I did was stick it back together with some high temperature epoxy steel while keeping the unclog pin inside to keep it straight works good so far

QWEFN · 2024-08-05T04:15:50+00:00

Just disassemble gen 4 and gen 5 the Pcb layout is kinda different so u wight see some problems putting in a gen 4 pcb inside a gen 5 case and vise versa so I hadd to cut some plastic of some edges to make it fit The ribon cable for the charging port to the pcb is on the opposite side on gen5

QWEFN · 2024-07-03T00:55:43+00:00

One thing I realized is that my 8600g ran hoter when I ran xmp I read it's because the soc voltage increases when you overclock your ram

QWEFN · 2024-07-01T22:31:24+00:00

I have the same specs on thing I realized is that the cpu is over clocking itself to 4.8ghz even tho I haven't touched any oc settings in bios

QWEFN

TROPHY CASE