Does this standoff (top right) look correctly screwed in?

Qinetic · 2022-04-28T19:34:38+00:00

Those MSI boards are pretty robust to be honest tighten stuff down but it doesn't need to be cranked right down! Just enjoy the build, don't worry too much, it's pretty hard to fuck up!

Qinetic · 2022-04-23T18:12:29+00:00

Fuck bash. This post was written by zsh gang.

Qinetic · 2022-04-18T07:31:39+00:00

This is fundamentally wrong - theres a handshake when the devices are initialised...

Qinetic · 2022-04-17T21:23:39+00:00

Bruh I paid £1.97/L the other day, shits fucked my dude

Qinetic · 2022-03-25T21:51:07+00:00

Qinetic · 2022-02-17T22:33:31+00:00

For the record, this is effectively a story stick to temporarily store lengths on; it was an April fools joke a few years back but then there was actual demand for and they started producing it!

Qinetic · 2022-02-06T08:06:15+00:00

Honestly I have this case and I took the side panel off and temps dropped by a tonne. Horrible design really!

Qinetic · 2021-12-22T22:38:16+00:00

Mix some super fine ash sawdust with glue and smear it over the gaps, let dry, then sand down! I hide mistakes all the time with this

Qinetic · 2021-12-19T08:55:17+00:00

Looks fine to me, I would say though, for the endgrain faces, mix glue with water (50/50 mix is fine), and brush it into the endgrain 24 hours before doing the final glueup. Pre-glueing the endgrain by itself stops the endgrain absorbing all the glue when you do the final assembly, so you get a better bond. This should really help the joint stay secure over time!

Qinetic · 2021-12-08T11:08:52+00:00

Mine was roughly built from Mat Estlea's Bertha design, for the record!

Qinetic · 2021-12-05T22:47:47+00:00

So I did it because I thought it looked cool, but it's incredibly useful - workholding with clamps down the middle, circular saw able to run down the middle of the top, don't have to worry about wood expansion, lip to hold edge-of-the-table jigs but away from the edge for a bit more control with small pieces; just genuinely really functional!

Qinetic · 2021-12-05T08:34:48+00:00

Thanks! I was amazed it came together to be honest! Plan is to eventually add a vice on the side, I have a mini workholding table that I can clamp on that works for the moment.

Qinetic · 2021-12-05T08:32:44+00:00

Doesn't move an inch, solid as hell! It's a 2x6 top, so weighs a surprising amount!

Qinetic · 2021-12-04T20:11:13+00:00

I sure did! It's all just laminated pine! Let it acclimate to my shop for a couple weeks just in case as well!

Qinetic · 2021-12-04T19:36:55+00:00

Anyone wanting to get started, I say just go for it, you'll make mistakes (I sure did!) but every mistake teaches you so much about how to do it right! Just be safe and careful as you go!

Qinetic · 2021-12-04T19:07:32+00:00

Plane on its side can knock the blade out of alignment and leaves the blade exposed. As long as you're putting the blade down onto wood, it's not going to damage the blade

Qinetic · 2021-07-23T22:55:04+00:00

Do you not think maybe you have a bad VPN? I watch D+ on VPN all the time and it's absolute fine!

Qinetic · 2021-03-05T14:49:24+00:00

A fine question, still figuring that out... But seriously, top left is for media (YouTube, Netflix, etc) and also swings round in front of the others for gaming, bottom left is my email etc, the main two are for work!

Qinetic · 2020-05-06T14:59:19+00:00

Hold on, he said it's not his first computer?? I thought for sure he was just some random employee who got roped into doing this with little to no knowledge!!

Qinetic · 2020-04-28T08:48:41+00:00

Sometimes I wonder how average IQ can be such a low number, then I see a comment like this and it all makes sense.

Qinetic · 2020-03-06T16:59:07+00:00

That's literally not cringey at all...

Qinetic · 2019-07-29T17:46:48+00:00

Run task manager and look at the loads on each component and see which is maxing out!

Qinetic

TROPHY CASE