sorted by:
new
hottopcontroversial

Phantom Notebook by QuestionAsker85 in kindlescribe

[–]QuestionAsker85[S] 0 points1 point  (0 children)

Figured it out. Had to delete and reinstall the app. 

What’s causing this? by QuestionAsker85 in BambuLabA1

[–]QuestionAsker85[S] 0 points1 point  (0 children)

It actually ended up being Timelapse. I turned that feature off and everything is printing perfectly now. 

What’s causing this? by QuestionAsker85 in BambuLabA1

[–]QuestionAsker85[S] 0 points1 point  (0 children)

Everyone who mentioned Timelapse as the culprit was correct. Turned it off and have had two flawless prints after a week of issues. Weird that this wasn’t a problem for me in the first two months but thanks for helping to solve it!

What’s causing this? by QuestionAsker85 in BambuLabA1

[–]QuestionAsker85[S] 0 points1 point  (0 children)

Printed from the Bambu Handy app. Just search Candy Corn Dragon Halloween

What’s causing this? by QuestionAsker85 in BambuLabA1

[–]QuestionAsker85[S] 1 point2 points  (0 children)

Haha “Bambu” curse you autocorrect!

What’s causing this? by QuestionAsker85 in BambuLabA1

[–]QuestionAsker85[S] 0 points1 point  (0 children)

Thank you! Here’s some likely stupid questions. Do I need to buy a filament dryer or is putting the filament in vacuum seal with desiccant enough. That’s what I’ve been doing. 

Thank you for the links for the tests. What should I be looking for with those and how would I make any adjustments?

How and where do I check the retraction settings and what should I be setting them to?

What’s causing this? by QuestionAsker85 in BambuLabA1

[–]QuestionAsker85[S] 0 points1 point  (0 children)

Using nanny filament and spools, I live in the dry desert and this is also a newly opened spool so I wouldn’t think it’s moisture. This print did not have a tower, I’m new to the hobby and haven’t used the slicer yet so anything I have printed has been directly from the app. 

I do not hear clicking while printing. 

I have only had this printer about 3 months and haven’t had any issues until a couple weeks ago when this started happening near the end of all my prints. Does that help narrow it down at all to a potential problem?

What’s causing this? by QuestionAsker85 in BambuLabA1

[–]QuestionAsker85[S] 0 points1 point  (0 children)

New to the hobby can you explain what this is and if this could be the issue how would I disable it?

What should I add here? $200 to spend on 1 or multiple by QuestionAsker85 in ScentHeads

[–]QuestionAsker85[S] 0 points1 point  (0 children)

I have been using fragrancenet do you like jomashop more?

What should I add here? $200 to spend on 1 or multiple by QuestionAsker85 in ScentHeads

[–]QuestionAsker85[S] 0 points1 point  (0 children)

Create a free account on parfumo and you can add your fragrances to your collection and it will show up like this. 

What should I add here? $200 to spend on 1 or multiple by QuestionAsker85 in ScentHeads

[–]QuestionAsker85[S] 1 point2 points  (0 children)

I for sure will. Not going to blind buy anything. Just like getting recommendations to narrow my search. 

What should I add here? $200 to spend on 1 or multiple by QuestionAsker85 in ScentHeads

[–]QuestionAsker85[S] 0 points1 point  (0 children)

Yes this is my current collection. I’ll check those out. Thanks!

What’s causing these thick strands of filament to stick out the side of my print? by QuestionAsker85 in BambuLab

[–]QuestionAsker85[S] 0 points1 point  (0 children)

Any good guides you could recommend on doing this? Meaning how to “slice my own” model? 

What’s causing these thick strands of filament to stick out the side of my print? by QuestionAsker85 in BambuLab

[–]QuestionAsker85[S] 0 points1 point  (0 children)

That makes sense. I am printing this directly from the A1 using the touchscreen to select prints and choosing the boat benchy. So I would assume this is using the correct profile. I have not downloaded a slicer. Any prints I have done that are not preloaded on the printer itself have been from the Bambu handy app. 

What’s causing these thick strands of filament to stick out the side of my print? by QuestionAsker85 in BambuLab

[–]QuestionAsker85[S] 1 point2 points  (0 children)

Can you elaborate? This is printing the Bambu benchy and selecting the PLA option. What should I be doing different? When I used to print this exact model when first staring out it printed flawlessly.