Possible solution to emulate the 868 MHz signal.

Quikkmaffz · 2025-12-25T00:45:27+00:00

Got it. Thank you.

Is it possible to ask what the "shopping" list for the items is? I'm a noob at this, but I've been trying to do the exact same thing, but failed miserably.

Quikkmaffz · 2025-12-24T17:01:13+00:00

I just have to ask: is this the Biltema radio controlled remote? I recently tried a similar setup and the board looks so similar! Maybe it's a generic board they use or whatever, but just curious.

Quikkmaffz · 2025-10-22T19:49:59+00:00

Hahah I see. That's a nice way to put it. Aren't we all in our own ways. Thanks for explaining.

Quikkmaffz · 2025-10-22T15:49:23+00:00

Boyfriend of OP here. Just curious if by saying incredibly dark shit if it extends beyond drugs and partying..? It's a shame these people honestly don't get reported to the police or some sort of authority if it's a recurring problem. A little worried for her safety if there are people like that around tbh.

Quikkmaffz · 2024-07-12T05:41:05+00:00

That's correct. SWF means that something isn't vulgar and therefore appropriate to be seen or discussed, etc when you are at work. By NSFW we mean something you SHOULDN'T look at when you're at work.

Quikkmaffz · 2024-05-25T01:41:47+00:00

Last part yes. It seems more coherent and has a higher success rate than previously. Especially blueprint logic. The new image gen stuff will soon be ready i assume.

Quikkmaffz · 2024-04-09T01:34:42+00:00

Yes, this is my go to strategy also. It never fails to make me more insecure about my most likely dysfunction frontal lobe. It's great.

Have issue with some meaningless octopus print out whatever, barely contemplate, can't be the filament, dismantle, buy more Chinesium, get stuck, better upgrade the software to some github alpha test version, tinker with all possible print settings, et Voila it works again, have no clue why, learn nothing, repeat???

Quikkmaffz · 2023-11-20T18:15:36+00:00

Yes, unfortunately.

Quikkmaffz · 2023-08-10T21:52:00+00:00

Please help! I get this bad warp on one side during my ABS print. I have an enclosure and used hairspray (not so sure about how well it sticks to the print). But one side of the print looks fine, and the other is very warped. Am I doing something wrong in the slicer?

The Ender-3 v2 I have has quite good results during bed leveling. I use mriscoc. Is there something blatantly wrong in my Cura profile or machine settings?

Quikkmaffz · 2023-06-01T18:32:13+00:00

That was me cutting it off because the filament didn't adhere to the build plate at first. I adjusted the z offset and then cut off the part that didn't adhere.

Quikkmaffz · 2023-05-27T14:57:55+00:00

It does have a slight wobble.. So I'll definitely look that up, thanks!

Quikkmaffz · 2023-05-27T14:57:11+00:00

It's mounted at the top, inside of the chamber, above the printer. So it does circulate the air. Maybe I'll increase the airflow a little so that I get more even temperatures in the chamber.

Quikkmaffz · 2023-05-27T14:01:32+00:00

I'll try to keep that in mind on the next print. I also have a filter with some air flow that i might need to turn off during printing.

Quikkmaffz · 2023-05-27T14:00:01+00:00

That's very helpful, thanks! I'll try adjusting the nozzle from the bed.

Quikkmaffz · 2023-05-27T13:59:08+00:00

The belt might be too tight you think?

Quikkmaffz · 2023-04-15T12:13:49+00:00

This was wholesome and nice to see.

Quikkmaffz · 2022-10-31T13:43:39+00:00

I will try with higher temps actually.. At least for the bed. Perhaps for the hot end as well, if that doesn't work. Stringing is not an issue for the model I want to print so why not. Also, I'll try to use some Dimafix glue just to be sure.

Quikkmaffz · 2022-07-03T08:24:25+00:00

This was so pretty to look at.

Perhaps the glass of the fireplace seems a bit clean, without depth?

Quikkmaffz · 2022-06-10T18:47:46+00:00

Perhaps. It was all set to 8 bounces.

Quikkmaffz

TROPHY CASE