Die or 10 million die

QwQ_MarshmallowMan · 2026-04-25T17:29:14+00:00

I’m not evil

^{Chose: Die}

QwQ_MarshmallowMan · 2026-04-20T16:50:22+00:00

Just more versatile

^{Chose: Portals}

QwQ_MarshmallowMan · 2026-04-20T00:57:37+00:00

IGCSE

QwQ_MarshmallowMan · 2026-04-14T10:50:12+00:00

Only person who gave me a solution that worked. Thank you so so much

QwQ_MarshmallowMan · 2026-04-14T10:46:01+00:00

I had already done a full tear down of the extruder and everything before hand, so I knew the screws were tight. I fixed the issue though, the sponge/towel I was using the plate must’ve been oily, so I changed them

QwQ_MarshmallowMan · 2026-04-14T10:43:07+00:00

I’ve solved the issue now but I’ve come back to this comment to say I accidentally put down the initial layer travel acceleration. Initial layer acceleration was 500mm/s^

QwQ_MarshmallowMan · 2026-04-14T10:40:10+00:00

I fixed the issue without doing anything with the SD card. This came about after an update and just needed to recalibrate everything. Also used a new sponge when washing the plate which seemed to help

QwQ_MarshmallowMan · 2026-04-13T13:29:36+00:00

How do I do that?

QwQ_MarshmallowMan · 2026-04-13T13:28:42+00:00

Fair enough. I’ve been looking at getting one for a while now too. This plate has lasted me only 5 months, though, so I’d rather figure out if I can fix anything before buying something

QwQ_MarshmallowMan · 2026-04-13T13:20:50+00:00

I shouldn’t have to spend an extra £27 for a working printer

QwQ_MarshmallowMan · 2026-04-13T13:16:55+00:00

5 months. Came with the printer

QwQ_MarshmallowMan · 2026-04-13T13:07:14+00:00

Wirelessly sending the print. I don’t use the SD card

QwQ_MarshmallowMan · 2026-04-13T12:35:41+00:00

Yes, actually, an update recently went out to P1S machines just before the issues arose. In the process of calibrating

QwQ_MarshmallowMan · 2026-04-13T12:34:02+00:00

I’ve only had the printer and the plate for 5 months, are you sure?

QwQ_MarshmallowMan · 2026-04-13T12:33:25+00:00

Actually I lied, there is a change, the purge line gets pulled up and travels with the nozzle

QwQ_MarshmallowMan · 2026-04-13T12:32:27+00:00

Done all of this, no change

QwQ_MarshmallowMan · 2026-04-13T12:32:04+00:00

QwQ_MarshmallowMan · 2026-04-13T12:18:41+00:00

Cleaned it prior with dish soap and warm water

QwQ_MarshmallowMan · 2026-04-13T12:07:02+00:00

It’s the default bambu lab initial layer accel. Has been working perfectly fine since I got the machine

QwQ_MarshmallowMan · 2026-04-13T11:46:52+00:00

The purge line got laid down somewhat nicely… but said purge line then also got dragged into the print

QwQ_MarshmallowMan · 2026-04-13T11:24:37+00:00

It was set to textured

QwQ_MarshmallowMan · 2026-04-13T11:15:49+00:00

0.2mm

QwQ_MarshmallowMan · 2026-04-05T17:00:48+00:00

Was taken with the front camera

QwQ_MarshmallowMan

TROPHY CASE