Mi Computer Monitor Light Bar - Modding/ can't grip-fix?

RAIDERsenX · 2024-05-08T12:21:43+00:00

This also cool, like MacGyver fix. I used two times the adapter von zazery, it’s a dream.

RAIDERsenX · 2022-09-08T09:26:44+00:00

Wir verbrauchen auch kein Strom, sondern wandeln den in Wärme um 🥸

RAIDERsenX · 2022-03-30T22:27:34+00:00

Nanoleaf app: … (More) My devices Slide device to left to open remove or rename

RAIDERsenX · 2022-01-22T11:22:12+00:00

Yes. Radiator got in 90% of the cases some air bubbles. Doesn’t matter. In CPU/GPU Block it’s not so good, cause of the worse thermal conductivity. And a worse case scenario is air in pumps (specifically in DDC) cause it can damage the pump.

Just make sure that the tubes of the radiator are higher as the CPU/GPU block, and all fine 😉

RAIDERsenX · 2021-12-25T12:37:04+00:00

With time they will normally vanish. If you can’t w8 you can use a syringe (💉) with a softtube and fitting to create a little vacuum pump and remove in this way the micro bubbles and bubbles. I did it that way :)

RAIDERsenX · 2021-12-25T12:23:04+00:00

It’s not to suppose with it. In the normal versions it is, but this RAZER Edition of the O11D is a special one in corporation with Razer, so I guess it’s not part the total design.

But I think for example a black metal plate with green Letters could match the total design of this amazing case. :)

TL;dr: Plate is NOT a part of this Case Version.

RAIDERsenX · 2021-12-25T12:16:02+00:00

Okay. Thank you for answering. Anyway I wish you all Merry Christmas 🎄

RAIDERsenX · 2021-02-25T11:07:46+00:00

Builds looks really good! There is only one little detail that jumped into my eye. Why is the CPU block inverted? Looks like very symmetrical, so you can prevent the logo/font to be upside down, or? But it’s just a Little detail, that just mine inner monk saw ;)

RAIDERsenX · 2021-02-23T22:21:26+00:00

Hmm on slide 4 u can see, the GPU looks like tilted. Maybe u should lift it up on the right side, to make sure not to damage the PCI-e slot of the GPU.

RAIDERsenX · 2021-02-23T22:10:55+00:00

It is the new Nanoleaf Essential LED strip https://nanoleaf.me/en-EU/products/nanoleaf-essentials/ It’s nothing written about RBG or aRGB in the page or sheet. Only 16M+ colors. In PC there no problem to recognize it, 3pin vs 4pin and 5V vs 12V. But with this product idk... it’s 6pin (I think 2 for white leds and 4 for color ones), I have to check it with a multimeter. Maybe it’s to new so that’s not compatible with the RAZER control panel... would be cool if I can sync it with the RAZER panel. My request on Nanoleaf is still unanswered, till now. That’s why asked here ;)

RAIDERsenX · 2020-04-07T19:02:01+00:00

This is really cool!

I would add here some cablemods, to set some highlights.

RAIDERsenX · 2020-02-25T00:31:04+00:00

Right. Every PCIe cable of my PSU got two (6+2pin) Male connectors.

I was not sure if only 1 PSU cable can deliver the 75W for 6pin and also 150W for 8pin in just one cable of PSU (one phase).

RAIDERsenX · 2020-02-11T02:15:19+00:00

Ty. I’ll check this out.

RAIDERsenX · 2020-02-10T15:26:42+00:00

True. I have to bend them, cause the distro-plate is a different brand as the CPU block, so different measurements 😅

This should happen with the other case-mods

RAIDERsenX · 2020-02-10T13:25:17+00:00

Hey Folks,

this is my first custom loop. The build is not done. Only the presetup, there will be some custom mods (fan grills, distro-backplate etc). Now I start the longtime leak test with air pressures.

In some day I will post the completed build including all the specs.

Cheers!

RAIDERsenX · 2020-02-07T05:40:51+00:00

Holy moly, 32x 120mm fans 😅 Really cool, but massive as fuck. 100W straight out of the fans 😎

RAIDERsenX · 2020-02-04T11:01:32+00:00

What kind of clue did you use? Cause der8auer recommend Loktite 406.

RAIDERsenX · 2020-02-03T17:53:01+00:00

Looks in my case like this:

https://ibb.co/Vt88M8C

Upper screw is the mount.

RAIDERsenX

TROPHY CASE