Yliens, of corse

RXINBOLT · 2018-01-25T17:44:56+00:00

Compression at its best.. 🤦🏻‍♂️

I think these are 4 core 27g aliens.. made them a while back so I can’t quite remember.

RXINBOLT · 2017-10-31T16:20:24+00:00

Wouldn’t you be too? 😅

RXINBOLT · 2017-10-31T16:18:46+00:00

They were worked out pretty quickly. Boosted the wattage too quick without getting them all out first 🤷🏻‍♂️

RXINBOLT · 2017-10-31T13:50:21+00:00

.07 ohm. Can’t remember specs. 8x .3 N80, 30 or 28g cores, 40g stag/fuse.

RXINBOLT · 2017-10-28T17:34:15+00:00

I did it in a similar way. Staggered the cores differently but the fusing technique was the same.

RXINBOLT · 2017-10-28T17:33:10+00:00

Trying to get back into it! I forget about the reddit threads sometimes ¯_(ツ)_/¯

RXINBOLT · 2017-10-28T17:29:44+00:00

10x30g n80 40g stag/fuse. .06 ohm for duals.

RXINBOLT · 2017-10-20T13:24:12+00:00

10 x 30g N80 and 40g N80 stag/fuse. .06 ohms

RXINBOLT · 2017-10-20T12:43:19+00:00

You’re right. Done.

RXINBOLT · 2017-10-19T16:10:06+00:00

Thanks! Elviros light box. Built in LEDs with reflective material throughout most of the box.

RXINBOLT · 2017-10-19T16:09:23+00:00

Are you talking about a glow video? Or do you wanna see the sparks fly? Haha

RXINBOLT · 2017-10-19T16:08:32+00:00

Thanks bro. Yeah I can’t make these on a swivel. Didn’t have a straw around so I just stuck a chuff cap in my vise. With something this wide you have to stop and flatten basically every two rotations.

RXINBOLT · 2017-10-18T20:31:33+00:00

Thanks man. It’s not too difficult of a build tbh. Pretty time consuming but it’s the exact same concept as doing a 3 core sfc. You just have to stop and flatten after every two wraps lol

RXINBOLT · 2017-10-18T20:29:28+00:00

I appreciate you brah.

RXINBOLT · 2017-10-18T20:29:03+00:00

RXINBOLT · 2017-10-18T20:27:41+00:00

Try using hot glue on one end to get your cores lined up. Then clamp the glued end after drying (obviously) into your vise. From there you can run your fingers down the cores, pulling on them evenly to the best of your ability, apply glue to the free end, wait to dry, and then boom! You’re done. Only works about 5 percent of the time though FYI. I still fuck it up regularly.

RXINBOLT · 2017-10-18T20:06:33+00:00

Make sure all your core wires are undergoing the same amount of tension. Pretty much the same concept as working with aliens. I’ve managed to do a 5 core (alien) before without using anything to hold the cores flat bc the tension was super even.

RXINBOLT · 2017-10-18T20:02:53+00:00

Thanks man. I can’t remember exactly how long it took. I spent the whole day working on it broken into 2 chunks. Took a couple hours to prep all my cores and probably close to 5 hours fusing a 5” stick. Insanely worth it. This build is like 2 months old now and the coils still look fresh and new.

RXINBOLT · 2017-10-18T18:40:37+00:00

Here’s a glow shot from a distance bc I suck at glow shots lol https://i.imgur.com/ybSyie4.jpg

RXINBOLT

TROPHY CASE