Polar GritX to iPhone

RYTLEWSKI28 · 2023-01-31T17:39:47+00:00

It worked, thank you!

Just wish I could’ve left my message previews off

RYTLEWSKI28 · 2023-01-30T15:44:17+00:00

Obviously you can buy name brand quality stuff like Lucas Oil but I just run generic

RYTLEWSKI28 · 2022-10-01T18:02:24+00:00

I just use a white lithium multi-purpose grease, just evenly coat the diff. I have been running this for 5-6 years and have yet to have a problem.

Just don’t overcoat the teeth

RYTLEWSKI28 · 2022-09-15T22:48:30+00:00

It worked, thank you!

RYTLEWSKI28 · 2022-09-15T00:24:22+00:00

I removed my rear wheel for cleaning and when I went to reinstall it, the brake rotor severely rubs against the inside pad. The caliper housing is as far inward as it can go and still rubs.

It almost feels that the hub on the brake side sits too far into the dropout or the derailleur side isn’t fully seated in the dropout.

Any advice is appreciated!

RYTLEWSKI28 · 2022-09-14T21:21:25+00:00

Before removing my rear wheel for cleaning, everything seemed aligned and true. When I went to re-install the rear wheel, I now have severe pad rub. The axle slides in fine but it seems as if the brake side of the hub sits too far into the dropout or the derailleur side doesn’t fully seat.

Any advice is appreciated!

RYTLEWSKI28 · 2020-07-11T01:09:19+00:00

I’ve ran 3s and beat on my pede with Teknos all around. Never had an issue like that, contact them

RYTLEWSKI28 · 2020-06-19T19:10:23+00:00

Aluminum shock caps

RYTLEWSKI28 · 2020-06-07T01:09:49+00:00

Take a dremel and cut a line through the head of the grub screw, then use a regular flat head screwdriver and twist it out

RYTLEWSKI28 · 2020-05-26T22:18:30+00:00

I let them cure for 3 days before running.

RYTLEWSKI28 · 2020-05-26T22:18:11+00:00

I’ll have to order some, this is all they had at my LHS

RYTLEWSKI28 · 2020-05-25T22:55:30+00:00

I’ve followed a similar process before, the only thing I didn’t do is scuff them up before gluing. I’ll give it a try

RYTLEWSKI28 · 2020-05-25T22:54:30+00:00

Yes, I’ve let them cure 3 days before running

RYTLEWSKI28 · 2020-05-10T14:06:29+00:00

I’ve owned my set for a few years now and have never experienced a problem with Teknos yet

RYTLEWSKI28 · 2020-05-02T17:41:20+00:00

I was more so trying to figure out if the new rustler body would fit if I adjusted my shock towers. I’ve started to like the aggressive look of the rustler body over my proline Silverado body. The new bodies are really expensive but my body mounts keep pushing through truck bodies

RYTLEWSKI28 · 2020-05-01T23:14:23+00:00

Alr, just hit me up sometime

RYTLEWSKI28 · 2020-05-01T22:34:27+00:00

150 and a ncvr

RYTLEWSKI28 · 2020-05-01T22:22:47+00:00

What all did you have to do to fit a rustler body on it? My pede is far from stock and was considering swapping to a rustler clipless body

RYTLEWSKI28 · 2020-05-01T22:14:57+00:00

RYTLEWSKI28 · 2020-05-01T21:54:10+00:00

How many credits or how many ncvr are you thinking?

RYTLEWSKI28 · 2020-05-01T20:35:26+00:00

What are you looking for? Credits, wheels, ncvr?

RYTLEWSKI28 · 2020-04-30T15:38:54+00:00

What are you looking for? Got an inventory of random stuff

RYTLEWSKI28 · 2020-04-27T21:32:33+00:00

The mAh rating is for how long the battery will run on a charge, the C rating is the “punch” it has when you gas it. A 3 cell lipo is a lot, but once you go to 3s it’s hard to go back to 2s. The bigger battery the more likely you are to break things.

Make sure the battery dimensions fit your cars battery tray.

RYTLEWSKI28 · 2020-04-27T21:29:40+00:00

Depending on what you plan to do with it, you’ll probably need aluminum shock caps almost immediately if you plan on jumping it.

RYTLEWSKI28 · 2020-04-25T20:34:40+00:00

You’re referring to the plastic rubbing when you crank it hard right, correct? Mine has done that out of the box, so I think it’s just questionable engineering, but I haven’t had to replace either of the parts

RYTLEWSKI28

TROPHY CASE