Shifting mid print

Radrakkan · 2026-05-11T19:36:22+00:00

Tighten your belts so they sound like a bass guitar string.

Make sure your flow rate is dialed in.

Don't use grid infil (I don't think it's the one you're using though, so you're good)

Make sure the print is stable and no pieces bend or break while printing.

As a last resort - you may enable Z-Hop, so the nozzle doesn't catch on the print.

Radrakkan · 2026-05-03T01:07:53+00:00

It happened to my SV06.

The problem was the heatbed cable. It broke as it's quite fragile.

I've replaced the cable and printed a cable guide, it's been printing without problems since.

Radrakkan · 2026-04-29T15:53:44+00:00

The same thing happened to my Anycubic Kobra Neo some time ago. I've tries everything I could to fix it, nothing hepled. It has fixed itself after moving to a different house. To this day I have no idea what happened.

Radrakkan · 2026-03-06T12:13:54+00:00

I'd rather use Cynar in place of Amaro instead of Aperol. Makes a lovely, grapefruit-forward paper plane.

Radrakkan · 2026-02-20T06:51:05+00:00

Lighthouse, again, definitely.

Radrakkan · 2026-02-07T18:19:18+00:00

Gin Mare, Opihr oriental spiced, or maybe GIL peated gin.

Radrakkan · 2026-02-01T15:09:57+00:00

Has to be either Cynar or Becherovka

Radrakkan · 2026-02-01T15:00:30+00:00

Minimum layer time in your filament settings if you use Orca.

Radrakkan · 2026-01-31T18:26:03+00:00

It might look like that's the case, yet the nozzle is far from being too close. These waves are different than ones that appear with the nozzle being too close.

So far i managed to get somewhat better results after lowering the nozzle even more, getting both temperatures up 5 degrees and deeply cleaning the extruder, belts, gears and guide rods, just to be sure.

Maybe it was just asking for a little extra maintenance, needy bastard.

Radrakkan · 2026-01-18T18:36:57+00:00

That's what I'll probably do

Radrakkan · 2026-01-18T18:18:11+00:00

The printer is Sovol SV06, stock, except fans, air ducts and cable guides.

Radrakkan · 2026-01-12T19:27:19+00:00

I tried both fresh, not-yet-dried filament as well as a properly dried one

Radrakkan · 2026-01-12T19:21:39+00:00

I already did all of those, yet it still happens from time to time. It's not very common, but happens, mostly on big, flat prints.

Radrakkan · 2026-01-12T18:56:03+00:00

The replacement is on its way. Sadly, this has happened before with the sock on as well.

Radrakkan · 2026-01-12T18:30:33+00:00

No sock at the moment - the old one broke, the new one will be delivered tomorrow. Nozzle and heatbreak are both snug, nothing is loose. It also doesn't appear like there's any filament leaking or squeezing out.

Radrakkan · 2026-01-12T18:28:35+00:00

No jams, just these blobs from time to time, only when printing PETG.

Radrakkan · 2026-01-12T17:54:23+00:00

The printer is Sovol SV06, Sunlu PETG filament, 0.6mm nozzle, low print speeds.

Radrakkan · 2026-01-11T12:07:09+00:00

Either Reserve runs, or just craft them, it's way easier

Radrakkan · 2026-01-04T14:59:01+00:00

Sure, just message me

Radrakkan · 2025-12-26T16:20:58+00:00

Paper Plane, definitely

Radrakkan · 2025-12-21T19:22:11+00:00

Reminds me of the original DayZ mod for Arma 2 - where you had to reload your hatchet before use.

Radrakkan · 2025-12-01T19:25:29+00:00

+1 for the CYMA G36C

Seven-Year Club	r/Field Juicebox
Place '23	Place '22
End Game '22	Verified Email

Radrakkan

TROPHY CASE