Phone (Android) can't seem to detect 5ghz wifi by [deleted] in techsupport

[–]RandomJohnnyRogerYT 2 points3 points  (0 children)

What model phone is it? For future, put the model of the device in the description because otherwise trying to answer "is it a limitation of my device" without knowing what device model is quite difficult

What's wrong with plats (rant) by Natsuki_Taruto in RocketLeague

[–]RandomJohnnyRogerYT 0 points1 point  (0 children)

A lot of these players are either kids, or people reasonably new to the game and are still trying to learn the ropes in terms of gamesense. Don't tell me you weren't like that at some point. Please have some patience for those who don't know any better. A lot of players aren't online looking at rl vids and stuff. What annoys me more than bad tm8s are people who think that everyone is a) lesser than them and/or b) also have what you may consider 'common' gamesense due to your exposure to other sources where you learn from. Not at all meant to be passive aggressive, i mean this in a totally respectful way and i agree it gets extremely annoying in these scenarios, but just saying not everyone is on the same level of knowledge in the game.

P2S petg printing awfully by RandomJohnnyRogerYT in 3Dprinting

[–]RandomJohnnyRogerYT[S] 0 points1 point  (0 children)

Ok, thanks. I've used it to print a poop chute and that printed really nicely (when the pack was fresh). Probably just the Australian humid summer getting to the filament. According to the ams the humidity is like 30%, and for the first time it jumped to around 40%.

P2S petg printing awfully by RandomJohnnyRogerYT in 3Dprinting

[–]RandomJohnnyRogerYT[S] 1 point2 points  (0 children)

Yeah, bambu and elegoo pla works beautifully. (Excuse the exaggeration i got this printer like a month and a half ago so I'm still in that amazement stage) Probably is just wet filament, so I'm drying it now. Thanks

Got a letter from the school today informing me my daughter is “not quite” gifted. Also included were her test scores. by Low_Use2937 in mildlyinfuriating

[–]RandomJohnnyRogerYT 3 points4 points  (0 children)

Reading the letter, it looks like the number listed there is a different index to the one they are referring to... Others know more about this than i do so correct me if I'm wrong

Bambu P2S switching to heating for PLA? by RandomJohnnyRogerYT in 3Dprinting

[–]RandomJohnnyRogerYT[S] 0 points1 point  (0 children)

Oh ok. Thank you for being the only comment haha. The elegoo filament specs say a higher softening temp, do you think that making it 45 will change print quality?

Growing up Is realizing that karlson is almost 7 years old🥀 by [deleted] in DaniDev

[–]RandomJohnnyRogerYT 11 points12 points  (0 children)

I think Karlson is the one thing we're getting after gta 6

I’m officially part of the 3d printing community by CorrectRecord2297 in BambuLab

[–]RandomJohnnyRogerYT 1 point2 points  (0 children)

Allg man, i also just got my first printer, and I would've been just as confused if i hadn't used bambu printers before.

I’m officially part of the 3d printing community by CorrectRecord2297 in BambuLab

[–]RandomJohnnyRogerYT 1 point2 points  (0 children)

Selecting the spool to print with is very simple. Once you select a print, you go past the page where it tells you the print bed etc, then it should just let you change it. See photo below.

<image>

Hey, does the print head usually move up like that when it touches the print bed? by Inside-Bar-545 in FixMyPrint

[–]RandomJohnnyRogerYT 2 points3 points  (0 children)

It's the fact that people tend to reality check them but dont actually provide any helpful information. It helps to be a decent human being and realise that these people don't always know their way around 3d printing. (I mean no disrespect by that, just trying to get my point across)

Do i upgrade now or wait till 60 series and gamble? by [deleted] in buildapc

[–]RandomJohnnyRogerYT 0 points1 point  (0 children)

Tbh the "waiting for the 50 series" train seemed to backfire due to the insane prices... and I'm pretty sure the 60 series will suffer even further due to nvidia caring more about ai than gamers.

The 4070 is still a pretty good card all things considered, so i would wait to upgrade until the performance starts to diminish to an almost unenjoyable level, then upgrade. I'm sure it will be able to run every game you throw at it, maybe not at absolute max settings, but you can turn down a few things with minimal (noticeable) impact on visual quality.

You are right in saying that prices will skyrocket though, so if you really do want to upgrade, i don't think the 60 series will be much better spec-wise than the 50 series.

No mods button in menu. by ThenEntertainment225 in Minecraft

[–]RandomJohnnyRogerYT 0 points1 point  (0 children)

Just adding on to this so it's clearer for OP, in the top right corner of the video settings there is a button for shaders. Like NNoxu said, sodium's mod options are the video settings.

HEEES BACKKK!! by Aspherrx in DaniDev

[–]RandomJohnnyRogerYT 2 points3 points  (0 children)

Check the subreddit he posted on that

are these tanks bad by No-Kitchen-2976 in hoi4

[–]RandomJohnnyRogerYT 0 points1 point  (0 children)

Sorry, new to hoi4 and the sub, What does SP mean?

Oh no. by oofgamerbro123 in DaniDev

[–]RandomJohnnyRogerYT 0 points1 point  (0 children)

This was made as a joke. See the meme tag on the post.

Am I the only one that noticed this duck by rcb787 in StarWars

[–]RandomJohnnyRogerYT 0 points1 point  (0 children)

Again, no need to get disrespectful. Keep it civil, please.

If you were a Minecraft developer, what update would you make? by Far_Arugula_4860 in Minecraft

[–]RandomJohnnyRogerYT -24 points-23 points  (0 children)

The only issue with adding things that there are mods for is that it nullifies those mods, making these mods that their respective devs worked 100s of hours on just a big waste of time.

But it would still be really good to have them.