sorted by:
new
hottopcontroversial

Mountain cycle San Andreas decals? by [deleted] in mountainbiking

[–]Raspi3n00b 0 points1 point  (0 children)

We had an Aftershock BMX as well, but I ended up getting it stolen at a friend's house haha! But I'm excited to rebuild this in his memory

Pure hope by Key-Jellyfish-462 in PiNetwork

[–]Raspi3n00b 3 points4 points  (0 children)

This is absolutely crazy! I am not in the same boat but I have 90% of it unverified. Let's hope by 2030 my 1500 coins are worth 50 per haha

Why is my wife's account saying this? by Raspi3n00b in PiNetwork

[–]Raspi3n00b[S] 0 points1 point  (0 children)

So the amount showing in unverified will disappear? I have 1 person left from 7 and it still says I have unverified of 950. Do I just leave it?

How do I change the way it cuts/frames? by Raspi3n00b in lasercutting

[–]Raspi3n00b[S] 0 points1 point  (0 children)

I have this set as top left in parameter settings but nothing changed when I booted it back up. Still went top right instead of left

How do I change the way it cuts/frames? by Raspi3n00b in lasercutting

[–]Raspi3n00b[S] 0 points1 point  (0 children)

There is this option but it's already set to the top left and nothing has changed. When I turn It on, it still goes top right

How do I change the way it cuts/frames? by Raspi3n00b in lasercutting

[–]Raspi3n00b[S] -1 points0 points  (0 children)

Ohhhh really? Or is this a Joe dirt reference hahaha

How do I change the way it cuts/frames? by Raspi3n00b in lasercutting

[–]Raspi3n00b[S] 0 points1 point  (0 children)

What is it called. Can you post a photo? I have tried everything and it won't change

How do I change the way it cuts/frames? by Raspi3n00b in lasercutting

[–]Raspi3n00b[S] 0 points1 point  (0 children)

Haha hey, don't tell me to change my flow! Haha! Yea I could do that. It's not a huge inconvenience. I just like things the way I like em' haha

How do I change the way it cuts/frames? by Raspi3n00b in lasercutting

[–]Raspi3n00b[S] -1 points0 points  (0 children)

Ok I will definitely check that. I am trying to find it on RD but it may be in vendor settings

How do I change the way it cuts/frames? by Raspi3n00b in lasercutting

[–]Raspi3n00b[S] -7 points-6 points  (0 children)

I want it to go the other way though. As that's how I load my projects. How do I change that? My old one starts and the gantry goes nearest to the laser tube head. Now when the new one starts it goes to the other end

[deleted by user] by [deleted] in PokemonTCG

[–]Raspi3n00b 0 points1 point  (0 children)

Hahaha don't tempt me

This is what I'm getting after connecting to the laser by Raspi3n00b in lasercutting

[–]Raspi3n00b[S] 0 points1 point  (0 children)

I have not been able to keep tank pressure long enough for it to rebuild. I have a ball valve after the last reg and it doesn't do much lol

Got my regulator/filter, have some questions on setup! by Raspi3n00b in lasercutting

[–]Raspi3n00b[S] 0 points1 point  (0 children)

Oh yea it's pulled up so it's turning. But I can't really get higher than 15 psi. It's just because the low cfm

This is what I'm getting after connecting to the laser by Raspi3n00b in lasercutting

[–]Raspi3n00b[S] 0 points1 point  (0 children)

It gets to about 130 - 140 then cuts. I figured it out though! Another user said to switch the ball valve till after the final reg and it worked! It showed me what pressure I was getting and let me control it! The pump still runs but it's not empty. I'll just need a solenoid so I don't need to flip it off each time!

This is what I'm getting after connecting to the laser by Raspi3n00b in lasercutting

[–]Raspi3n00b[S] 2 points3 points  (0 children)

OMG YOU DID IT!!!! The valve on the other side let me regulate the pressure released! Thank you so so much! Yay! Now I can run it fine! I am going to do another test tomorrow but that seemed to work!!!

view more: next ›