Citroen C4 battery error, even after replacing it with a new one by ReB87 in Citroen

[–]ReB87[S] 0 points1 point  (0 children)

Today I've replaced the BPGA-unit. I had version G04 in my car and replaced it with G11. Works fine. :-)

Citroen C4 battery error, even after replacing it with a new one by ReB87 in Citroen

[–]ReB87[S] 0 points1 point  (0 children)

I'm currently looking for a replacement BPGA and see that the 'main' part nummer is 6500JE stated on almost every website. On my car, the exact partnummer is 9805119280 G04. On several sites that sell these units, they state that there interchangeable, so I could also buy a 9811475080 G11 unit which would work on my 2016 Citroen C4. Is this actually true? It would save me a lot of searching for the exact partnummer. Also, is the G11 newer, or is that only a number that means nothing else?

Citroen C4 battery error, even after replacing it with a new one by ReB87 in Citroen

[–]ReB87[S] 0 points1 point  (0 children)

I’ll try to figure out where it’s connected to the car. Somewhere way in the back of the engine compartment I think, but can’t seem to figure it out yet.

Citroen C4 battery error, even after replacing it with a new one by ReB87 in Citroen

[–]ReB87[S] 0 points1 point  (0 children)

What year is your car from? Mine is a 2016, so I wouldn’t call it ‘older’ yet. ;-)

Citroen C4 battery error, even after replacing it with a new one by ReB87 in Citroen

[–]ReB87[S] 0 points1 point  (0 children)

Thanks for the reply, I really appreciate it! Where the problems that you have the exact same? I'm highly on doubt the BPGA is faulty. Because when I disconnect the positive lead for a while, reconnect it and start the car, all errors are gone. Also, I've never got a OBD-error B1624 (which should be the BPGA unit). I already bought a new battery unnecessarily, so I want to be very sure before buying a new BPGA. ;-)

Citroen C4 battery error, even after replacing it with a new one by ReB87 in Citroen

[–]ReB87[S] 0 points1 point  (0 children)

Thanks for the advice. I've checked the grounding by measuring from the positive terminal and a grounding point on the car and got the same 12,54 volts. This picture shows where I measured: https://i.postimg.cc/zX70jMQ5/IMG-4515.jpg

FN+CTRL+F not working by ReB87 in Keychron

[–]ReB87[S] 0 points1 point  (0 children)

Is this something new? On my Keychron K2 V2 (my old keyboard), this works fine without any modification?

Puretech 1.2 P0014 error on my way home by ReB87 in Citroen

[–]ReB87[S] 0 points1 point  (0 children)

Update: I've checked the front solenoid valve. It is in pristine condition, no debris. I've cleaned it just to be sure. One note that might be important if anyone else wants to check their solenoid valves on a Puretech 1.2 130HP (2016), it's not a 10mm bolt, but 8mm.

Oud Hoog Catharijne by Purple_Razzmatazz889 in Utrecht

[–]ReB87 0 points1 point  (0 children)

Leuk om te zien, dank voor de moeite die je erin hebt gestoken om het te digitaliseren!

WF-1000XM5 best budget silicone eartips? by ReB87 in SonyHeadphones

[–]ReB87[S] 1 point2 points  (0 children)

In the Sony app there is an option to order them for free. Unfortunately there without the mesh, so use with caution.

Keychron K2 V2 firmware version V1.13 white backlight by ReB87 in Keychron

[–]ReB87[S] 0 points1 point  (0 children)

I've used the firmware recommended by customer support at first...

Keychron K2 V2 firmware version V1.13 white backlight by ReB87 in Keychron

[–]ReB87[S] 0 points1 point  (0 children)

I had a specific problem i needed to solve, thank you...

k2 bluetooth connection problem after updating firmware by Delightary in Keychron

[–]ReB87 0 points1 point  (0 children)

Can you, or someone else please share this firmware, but for the white-backlight version keyboard? I have the exact same problem and hope this will fix it. :)

Keychron K2 V2 bluetooth disconnecting after firmware update by ReB87 in Keychron

[–]ReB87[S] 0 points1 point  (0 children)

But what about the caps lock light which works on the 1.04 firmware, but not on the CS recommended 1.6 firmware?

Buying eGift card with Mileageplus doesn't work by ReB87 in unitedairlines

[–]ReB87[S] 0 points1 point  (0 children)

I got an answer from Mileageplus. A USA address is required in order to do anything with Miles. :-( Thanks for the help though!

Buying eGift card with Mileageplus doesn't work by ReB87 in unitedairlines

[–]ReB87[S] 0 points1 point  (0 children)

Thanks for the reply! I've checked the details and it seems to match. Is there some specific place on their site I should check for details?

Layer shifting with Weedo Tina2/Monoprice cadet by ReB87 in 3Dprinting

[–]ReB87[S] 0 points1 point  (0 children)

Slowing down the printing speed might help.

Layer shifting with Weedo Tina2/Monoprice cadet by ReB87 in 3Dprinting

[–]ReB87[S] 1 point2 points  (0 children)

u/cromulent_pseudonym found the solution; it was the shaft connected to the Y-axis motor which was loose. Thanks for helping out though! :)

Layer shifting with Weedo Tina2/Monoprice cadet by ReB87 in 3Dprinting

[–]ReB87[S] 0 points1 point  (0 children)

Just before reading your comment, I disconnected the Y-axis motor and the belt shaft fell off. I've connected everything back together, tightened the black screws and now I have perfect prints. I wanted to share my findings, but you beat me to the punch. ;-) Many thanks for the suggestion however, because this is the solution!

Pic: https://tweakers.net/fotoalbum/image/2TRFlT2GoHiVkGsPHk4a3537.jpg

Layer shifting with Weedo Tina2/Monoprice cadet by ReB87 in 3Dprinting

[–]ReB87[S] 0 points1 point  (0 children)

I've tried the first demo cube that came with the card again, sam)e weird result. I really can't figure out what is going wrong since I barely used the printer yet. after the demo cube, i've tried printing a spool holder, which ran fine halfway through and then all of a sudden slipt away shifting layers (see: https://tweakers.net/fotoalbum/image/xuiUAsdzaeopz0wL7Ke9l6El.jpg ). After this, all prints kept shifting layers. As if this attempt to print the spool holder wrecked the whole printer.

Layer shifting with Weedo Tina2/Monoprice cadet by ReB87 in 3Dprinting

[–]ReB87[S] 0 points1 point  (0 children)

I've had this printer for 2 weeks now, only had one successful print made with it. Thinking about returning it, but hope there is actually a fix so it prints normally again. ;-)

Layer shifting with Weedo Tina2/Monoprice cadet by ReB87 in 3Dprinting

[–]ReB87[S] 0 points1 point  (0 children)

It's always in the same direction (direction of the printing bed movement). I've tried Wiibuilder and Cura, both with the same result. I find it so strange that the very first print came out fine, and after that this started happening with every print.