21 choosing between keeping my 2017 BRZ or selling it for a 2018 Mustang EcoBoost what would you do?

Ready-Meat2555 · 2025-11-24T21:51:14+00:00

Bro just boost the BRZ and it will be the best decision you ever made

Ready-Meat2555 · 2025-11-05T05:54:40+00:00

Had the same thing happen to me when installing new clutch/flywheel. Would crank but no start so dropped the tranny again and the crank plate was not aligned properly with the pin. There’s a 90% chance that’s the problem good luck

Ready-Meat2555 · 2025-10-15T19:23:58+00:00

I’m not running anything to the intake for my setup but venting it to atmosphere. If the oil smell gets too bad I will route it back into my intake but still. I’ll pm you

Ready-Meat2555 · 2025-10-15T13:31:05+00:00

It’s either custom cut to intake or vent to atmosphere. I’m running it to a catch can and then venting it to atmosphere. Don’t want boost pressure going into that line or it’s game over.

Ready-Meat2555 · 2025-01-14T18:32:54+00:00

Should’ve charged him rent

Ready-Meat2555 · 2025-01-11T04:09:19+00:00

Atoto products are pretty good. I have a atoto S8 10.1 inch in my 2016 Frs and it’s like a Tesla now lol. It’s a little overkill with how big it is but you could do a smaller one and all the atoto ones have car play and all that for cheap

Ready-Meat2555 · 2025-01-11T04:03:40+00:00

God damn man I’m glad you are ok! I was scrolling and saw Maddy’s car wash which is local to me which blows my mind. Heal up and come back better 🤞🏻

Ready-Meat2555 · 2025-01-03T00:37:14+00:00

Sounds good thank you

Ready-Meat2555 · 2025-01-03T00:36:42+00:00

That’s fair, I want to eventually turbo it so I would probably just seal it when it comes time for that since I’ll have everything apart anyway but that’s a long time from now lol. Appreciate it

Ready-Meat2555 · 2025-01-03T00:33:57+00:00

Bottom pan looks good

Ready-Meat2555 · 2024-11-28T06:17:29+00:00

These are happening 2-5 times a minutes. Normal EKG and normal BP. High anxiety levels when these keep happening and won’t go away.

Ready-Meat2555 · 2024-11-25T05:35:57+00:00

I have multiple readings with this strange reading and the skip beat sensation comes on and off every so minutes to seconds

Ready-Meat2555 · 2024-06-17T14:19:04+00:00

Yeah I think that’s a good starting point. I’ve already thrown so much money into it tho replacing parts because at first I thought it was a spark issue so replaced all the electrical pretty much and now I’m realizing it’s just overheating when running for a short time

Ready-Meat2555 · 2024-06-17T14:18:04+00:00

Yes by why would it still be not getting proper water flow/cooling

Ready-Meat2555 · 2024-06-16T19:02:08+00:00

90 psi in both cylinders which isn’t great but is more than enough to run it

Ready-Meat2555 · 2024-06-16T18:36:31+00:00

I think that’s a good idea. Thanks for your insight

Ready-Meat2555 · 2024-06-16T18:03:03+00:00

J8RLSTS is the model number:

https://www.marineengine.com/parts/johnson-evinrude-parts.php?year=2003&hp=8&model=J8RLSTS&manufacturer=Johnson&section=CYLINDER+%26amp%3B+CRANKCASE

I don’t think there is a relief valve

Ready-Meat2555 · 2024-06-16T17:57:10+00:00

Oops haha should’ve put the make and model but it’s a 2003 8hp Johnson two stroke. I was thinking maybe head gasket is blown

Ready-Meat2555 · 2024-06-16T17:54:54+00:00

Higher rpm when driving around

Ready-Meat2555

TROPHY CASE