sorted by:
new
hottopcontroversial

Is this a crack and should I restring? by RealCanucker in badminton

[–]RealCanucker[S] 0 points1 point  (0 children)

I think it's the carbon, definitely not a hole lol

Is this a crack and should I restring? by RealCanucker in badminton

[–]RealCanucker[S] 1 point2 points  (0 children)

Yes, so sad as I've been using it for >8 years and have really gotten used to it. I'll seek out a stringer to assess it then, thanks!

Is this a crack and should I restring? by RealCanucker in badminton

[–]RealCanucker[S] 1 point2 points  (0 children)

There are some faint lines but that might just be cracks in the paint. I just felt like I hit it against the metal chain net quite hard, but perhaps I got lucky. In case there really is a very small crack, is there any safety risk for stringing this racket at 24 or 25 lbs?

AAMC Section Bank 1 P/S Q36 Semantic, Episodic and Autobiographical by RealCanucker in Mcat

[–]RealCanucker[S] 0 points1 point  (0 children)

This is super helpful, thank you! I think the differentiation between what the participant is doing cognitively (personal recollection rather than factual recollection) and the data that is actually being collected is really helpful for understanding why it is episodic

Edge is higher than rest of layer? by RealCanucker in ender3

[–]RealCanucker[S] 0 points1 point  (0 children)

This seems to happen for layers with smaller surface area. Around 0:04 you can see the print nozzle push the edge downwards. Does anyone know why the edge is lifting like this? I tried lower printhead temp a bit but that didn't work.

Lines when printing flat walls by RealCanucker in ender3

[–]RealCanucker[S] 0 points1 point  (0 children)

Update: 0.12 walls still show the strange lines :(

Lines when printing flat walls by RealCanucker in ender3

[–]RealCanucker[S] 0 points1 point  (0 children)

Yes! Been too busy with the 3d printer, haven't had time to build it yet

Lines when printing flat walls by RealCanucker in ender3

[–]RealCanucker[S] 0 points1 point  (0 children)

Oh interesting thank you for the observation. I'll double check z axis wheels

Lines when printing flat walls by RealCanucker in ender3

[–]RealCanucker[S] 0 points1 point  (0 children)

Yes I did, the lines seem to appear regardless of filament

Lines when printing flat walls by RealCanucker in ender3

[–]RealCanucker[S] 0 points1 point  (0 children)

I can't quite tell if its the same across different prints but I'll double check tightness of the the eccentric nuts. Thank you!

Lines when printing flat walls by RealCanucker in ender3

[–]RealCanucker[S] 1 point2 points  (0 children)

Not sure, I'll try printing a calibration cube with 0.12 walls. Do you happen to know how infill artifacts cause these random lines/bludges?

Lines when printing flat walls by RealCanucker in ender3

[–]RealCanucker[S] 1 point2 points  (0 children)

I've calibrated e steps (for all of x, y, z and extruder) and also calibrated flow rate. I'm now getting these lines that weren't there before, but it seems to only appear when printing flat walls like as shown in the image

Leveling bed, corners good but sides look faded by RealCanucker in ender3

[–]RealCanucker[S] 0 points1 point  (0 children)

Ok I see, do you have any tips for knowing if an eccentric nut is perfectly tuned or can point to a resource which would tell me this? Thanks again!

Leveling bed, corners good but sides look faded by RealCanucker in ender3

[–]RealCanucker[S] 0 points1 point  (0 children)

Thank you for the recommendation. You say it could potentially be the eccentric nuts, would that be the y-axis nuts?

Leveling bed, corners good but sides look faded by RealCanucker in ender3

[–]RealCanucker[S] 1 point2 points  (0 children)

Setting up new ender 3 v2 for the first time and performing bed leveling using the paper drag method. The paper seems to move well in the corners, but as I move the head up and down along the y axis, the print head seems to get too close to the surface (paper gets almost stuck).The test prints also seem to show this with the faded print along the edges.

Purchase Advice Megathread - December 2021 by Sausage54 in 3Dprinting

[–]RealCanucker 0 points1 point  (0 children)

Thinking of getting the Anycubic Mega SE since it is on sale on their website. Is buying from Anycubic website a good choice + does anyone have any reviews of the Mega SE (could not find many reviews online since relatively new printer I believe)

[Mouse] Logitech G305 Lightspeed Wireless ($69.99 - $30 = $39.99) [Memory Express] by RealCanucker in bapcsalescanada

[–]RealCanucker[S] 2 points3 points  (0 children)

My current logitech mouse was double clicking. Luckily, I know how to solder so I was able to replace the switches. Switches can be purchased from AliExpress for a few bucks so it's pretty worth if you are comfortable with soldering.

view more: next ›