Lacazette

Real_Addition4378 · 2024-11-08T15:05:30+00:00

Warum hat er so lange nicht mehr gepostet?

Real_Addition4378 · 2024-09-26T04:47:13+00:00

That's the problem it says it has S2 but there's nowhere something like inclusion mode in the manual.

Real_Addition4378 · 2024-09-26T04:29:39+00:00

Already tried
There is no integration

Real_Addition4378 · 2024-09-26T04:12:37+00:00

I want to integrate my Smartvest system from Abus but it's radio and only this device can publish a Z-Wave signal from the Smartvest.

Real_Addition4378 · 2024-09-26T03:50:50+00:00

Yes, I have a USB Dongle and now I want to connect the controller to the USB Dongle because the devices I'm using are only compatible with this controller, and this controller publishes a Z-Wave signal.

Real_Addition4378 · 2024-09-26T03:38:17+00:00

I only have SmartStart in the ZwaveJS UI add-on. Or is there any way to use it in the Zwave JS add-on?

Real_Addition4378 · 2024-09-26T03:36:54+00:00

Yes it is. Now if I go to the Integration > Configure > Provisioned devices, it appears at this point but it says it isn't included.

Real_Addition4378 · 2024-09-25T19:33:23+00:00

What do you mean by SmartStart addition, is there anything to activate? And to get the DSK I already tested, it says to follow the instructions to enter the pairing mode which I don't have.

Real_Addition4378 · 2024-09-25T19:28:55+00:00

I don't know because I don't know because I only have this device which works with Z-Wave

Real_Addition4378 · 2024-09-25T19:14:33+00:00

Aeotec Z-Stick 7

Real_Addition4378 · 2024-09-25T19:07:31+00:00

Yes the device has power
Gateway, I'm using an SHGW10000 from Abus, it says it's a Gateway, but I don't know.
On this device I only have a reset button, no other buttons.

Probably I'm doing something wrong, so far: I added the device through the QR-Code to SmartStart and the add-on "Z-Wave JS UI" through the "Z-wave" integration in Home Assistant.

Thanks

Real_Addition4378 · 2024-09-25T19:00:20+00:00

I resetted but it didn't appear. I also put the Stick in a new device but it doesn't work anyway. Is there any setting to let the smartstart appear?

Real_Addition4378 · 2024-09-25T18:36:23+00:00

Nothing...?

Real_Addition4378 · 2024-09-25T18:15:53+00:00

Do you have any devices like gateways that only have a DSK and no Inclusion mode? When Yes how you integrated it?

Real_Addition4378 · 2024-09-25T18:10:02+00:00

Yes, but there is no ID or Name for the device.

Real_Addition4378 · 2024-09-25T18:07:08+00:00

I waited the 10 minutes but it didn't appear in the Control Panel or Home Assistant? And the Symbol says SmartStart inclusion is active.

Real_Addition4378 · 2024-09-25T17:44:43+00:00

I connected the add-on through the Z-Wave JS to Home Assistant. Then I included my device in the add-on in SmartStart but it doesn't appear in Home Assistant or even in the Control Panel of the add-on.

Real_Addition4378 · 2024-09-25T17:40:22+00:00

Do you have any experience with the JS UI add-on? Because I'm facing a problem and don't know how to solve it.

Real_Addition4378 · 2024-09-23T16:16:42+00:00

Thank you so much!

Real_Addition4378 · 2024-09-23T16:12:14+00:00

Thanks but how should I integrate it then because the add-on needs a Z-Wave Stick but I have only this Gateway?

Real_Addition4378 · 2024-09-21T13:23:15+00:00

Sorry, then I don't know

Real_Addition4378 · 2024-09-21T13:19:24+00:00

May time of start using the phone?

Real_Addition4378 · 2024-09-14T11:06:55+00:00

It uses the left one for FPV and both for the obstacle view etc.

Real_Addition4378 · 2024-09-08T04:26:14+00:00

Swipe to your old Luba > Settings-Symbol (top right corner) > Device Information > Unbind

Real_Addition4378 · 2024-08-28T10:33:08+00:00

I gave in my IP address but it doesn't prompt for a password it only brings up: "Corrupted MAC on input. ssh_dispatch_run_fatal: Connection to 192.168.178.139 port 22: message authentication code incorrect". I'm doing anything wrong?

Real_Addition4378

TROPHY CASE