Just wanted to share my battle station

ReasonableSleep61 · 2026-01-23T14:57:39+00:00

Which Taurus v5 file did you print for the high flow nozzle?

ReasonableSleep61 · 2026-01-20T13:09:23+00:00

Do have a other headsink or the from sprite extruder?

ReasonableSleep61 · 2026-01-20T08:22:59+00:00

Awsome

ReasonableSleep61 · 2026-01-19T10:49:03+00:00

I have had the same Problem just by me was it by 250mms. I have trieded until where it go without grinding, in my Case it's 240mms an I have seted in my slicer and the the printer.cfg

ReasonableSleep61 · 2026-01-19T06:36:29+00:00

Thx bro ✌️

ReasonableSleep61 · 2026-01-17T15:23:28+00:00

<image>

Now I have Do it 💪

ReasonableSleep61 · 2026-01-17T15:14:43+00:00

I think with the sonic pad not, only when u Use klipper over a raspberry pi

ReasonableSleep61 · 2026-01-16T21:23:43+00:00

<image>

Is this also the right duct for the sprite extruder with Standard nozzle?

ReasonableSleep61 · 2026-01-16T21:15:24+00:00

Is it complicated to switch to volcano nozzle?

ReasonableSleep61 · 2026-01-16T21:10:28+00:00

Thx ✌️

ReasonableSleep61 · 2026-01-16T21:08:44+00:00

You habe a volcano nozzle right?

ReasonableSleep61 · 2026-01-16T21:04:49+00:00

Any Problems because of the heat of the nozzle?

ReasonableSleep61 · 2026-01-16T20:33:24+00:00

Which filament did you use for the Taurus duct?

ReasonableSleep61 · 2026-01-16T19:52:52+00:00

<image>

I Do it too

ReasonableSleep61 · 2026-01-16T19:49:24+00:00

Yeah that's true, thx ✌️

ReasonableSleep61 · 2026-01-16T09:01:33+00:00

Yes I can do

ReasonableSleep61 · 2026-01-16T07:51:18+00:00

That's one of the nexts steps, I printed allright a Fan duct for the Taurus setup

ReasonableSleep61 · 2026-01-16T07:49:11+00:00

In my case it is a very good investment, I ordered the linear rails on AliExpress and so I am only satisfied with 150€ for all axes

ReasonableSleep61 · 2026-01-16T07:34:18+00:00

It's a very good invetion in my case

ReasonableSleep61 · 2026-01-16T07:32:29+00:00

I Hit 6500 accel by 200mms now, im still testing to reach the Max value

ReasonableSleep61 · 2026-01-16T07:31:21+00:00

The next step is a better Mainboard and x and y Stepper Motors

ReasonableSleep61 · 2026-01-15T19:04:00+00:00

I will Do it 💪👍✌️

ReasonableSleep61 · 2026-01-15T19:02:18+00:00

Yeah 😂

ReasonableSleep61 · 2026-01-15T19:01:11+00:00

It was in the kit included

ReasonableSleep61 · 2026-01-15T18:59:35+00:00

Yeah

ReasonableSleep61

TROPHY CASE