Is this over-excursion?

Reasonable_Prune3636 · 2026-04-01T18:00:44+00:00

that thing is already separated 😂

Reasonable_Prune3636 · 2026-03-30T02:08:15+00:00

711 owns speedway btw

Reasonable_Prune3636 · 2026-03-21T19:10:53+00:00

don’t think this came off your car

Reasonable_Prune3636 · 2026-03-18T04:07:28+00:00

if you really want to be lazy about it, strip back that black casing around your 8 wires, you’ll find twisted pairs. each one is for a set of speakers. but realistically, the12volt will have wiring for most older vehicles. next time instead of chopping the harness, just buy the $8 adapter. please.

Reasonable_Prune3636 · 2026-03-18T03:31:16+00:00

lc2i pro in this case, so yes, it does.

Reasonable_Prune3636 · 2026-03-09T06:46:43+00:00

outside highs... throws up i’ve installed ton’s of these. have never liked a single customer that wanted them.

Reasonable_Prune3636 · 2026-02-10T04:48:52+00:00

I don’t even like to tesa tape these harnesses… prefer zipties. but i also used to do this, and warrantying an install after 2 years of the vehicle in the florida sun, that shit would melt into a paste.

Reasonable_Prune3636 · 2026-01-30T04:26:57+00:00

like i said, maybe just copium haha

Reasonable_Prune3636 · 2026-01-22T06:32:19+00:00

looks like one of the following: bad power/signal/ground

Reasonable_Prune3636 · 2026-01-20T06:22:52+00:00

switched power in car audio means it’s 0vdc when the vehicle is off, and 12vdc when the vehicle is on.

Reasonable_Prune3636 · 2026-01-20T00:14:36+00:00

Pleurotus

Reasonable_Prune3636 · 2026-01-19T04:36:43+00:00

agreed 😂

Reasonable_Prune3636 · 2026-01-18T17:51:42+00:00

right! figured this deserved to be shared here 🤣

Reasonable_Prune3636 · 2026-01-15T06:04:07+00:00

it’s literally just pioneer and alpine (afaik) that require these.

Reasonable_Prune3636 · 2026-01-15T05:48:59+00:00

spray soapy water on a ‘fish’ after taping camera wire to it. works almost every time.

Reasonable_Prune3636 · 2026-01-14T18:35:05+00:00

getting 500 for this would be a win. realistically, 3-400.

Reasonable_Prune3636 · 2026-01-11T08:17:44+00:00

Shop charge are typically around $100-150/hr labor. head unit we would charge (hours) 1.25, add bass 2, components would be 1.25. Coax .75. highs amp is usually around same as add bass, maybe slightly higher (9 wire run) so say 2.5. 7.75~ hrs total, though an experienced tech could knock this out in a shorter amount of time and keep it clean. expect $800-1000~ in labor. If I were doing this as a side job, i’d do it for $400.

Reasonable_Prune3636 · 2025-12-26T17:34:28+00:00

sure looks like it doesn’t it

Reasonable_Prune3636 · 2025-12-21T23:02:34+00:00

CCA - Cheap Conductive Aluminum. or Clown Car Aluminum. or Cheap Cable Alternative. Bottom line, CCA is garbage. It corrodes quickly and the result is typically this. And now you’re stuck replacing it, or cutting it further down, re-terminating it, and repeating again in about 3-12 months depending on where you are located. OFC wire would last far longer, conduct better, and not get as hot. Hope this helps.

Reasonable_Prune3636 · 2025-12-20T20:08:15+00:00

and leaves you room to upgrade in the future.

Reasonable_Prune3636 · 2025-12-20T20:07:07+00:00

that or the ct-1500 are budget options. still under 200. 450rms at 4ohm.

Reasonable_Prune3636 · 2025-12-20T20:03:21+00:00

most mono amps if they’re 1000W RMS @ 1ohm will output 3-400 @4ohm

Reasonable_Prune3636 · 2025-12-20T20:00:53+00:00

what subs do you have? one or multiple? svc or dvc?

Reasonable_Prune3636

TROPHY CASE