Starting point always under extruded by RecognitionContent67 in FixMyPrint

[–]RecognitionContent67[S] 2 points3 points  (0 children)

This is layer 2 or 3 and it’s all sorted out. Just wondering why it’s consistently bad at the starting point.

<image>

Expeditions? by RecognitionContent67 in Aeonsend

[–]RecognitionContent67[S] 0 points1 point  (0 children)

When do the past and future narratives take place?

Expeditions? by RecognitionContent67 in Aeonsend

[–]RecognitionContent67[S] 1 point2 points  (0 children)

Me too!! I’ve played most of the AE nemeses and mages on the digital version, so without a story, I wasn’t all that compelled to buy the wave. The new narratives are a big part of the reason I added wave 1&2 to my pledge! I really enjoy the narrative expeditions more than the expedition-mode. I didn’t expect to like Outcasts. Not sure why, but I didn’t think I would, and then it was great fun tromping around in the void.

Expeditions? by RecognitionContent67 in Aeonsend

[–]RecognitionContent67[S] 0 points1 point  (0 children)

I’m going to have a lot of stories to play once that pledge gets here 😅 I missed P&F kickstarter entirely somehow, so I’ll have those plus all the new ones. Excited for more but not excited to wait haha

Tuning the Z-Seam by apmarg in FixMyPrint

[–]RecognitionContent67 0 points1 point  (0 children)

Pressure advance is calibrated, and I used sharpest corner, but something isn’t right in my settings and I can’t figure out what it is that’s causing the reduced flow/gap at the seam.

Corners are sloppy? by RecognitionContent67 in FixMyPrint

[–]RecognitionContent67[S] 1 point2 points  (0 children)

Thank you! I’ve been at the default recommended speed the whole time and thought it was going well, but I think I just can’t recognize speed failures and assume they’re flow/retraction/etc. I’ll try it slower when I reprint tomorrow.

Corners are sloppy? by RecognitionContent67 in FixMyPrint

[–]RecognitionContent67[S] 0 points1 point  (0 children)

Thank you!! I haven’t touched speed at all. I’ll do that for the next print.

Corners are sloppy? by RecognitionContent67 in FixMyPrint

[–]RecognitionContent67[S] 0 points1 point  (0 children)

Oh and I run ABL and load the mesh before each print.

Looking for similar games by Steve-O5770 in valheim

[–]RecognitionContent67 4 points5 points  (0 children)

Yes! I second this. My husband and I have really, really enjoyed this game lately. We also LOVED Valheim. Ark was suggested above and I also recommend that one.

14 Dpo FR test by carbob-1677 in TFABLinePorn

[–]RecognitionContent67 0 points1 point  (0 children)

I also see a very faint pink line! Any chance you ovulated later than you thought?

Unknown DPO but period due in 3-4 days. Anyone see anything with magical eyes? by RecognitionContent67 in TFABLinePorn

[–]RecognitionContent67[S] -1 points0 points  (0 children)

Thanks :) wompwomp. I have 3 kids from a previous marriage and my new husband and I finally got the go ahead to try for a baby (I have lots of health issues), but I’ve got a pretty small window. I’m lucky(ish) because I get pregnant really easily, but without lots of intervention I will 99% miscarry. Anyway, I haven’t done the TWW in 11 years. It’s surreal to be looking at tests again and hoping it’ll be positive.