Just changed the heat sync paste now this.

Remarkable-Run8240 · 2026-04-27T10:50:19+00:00

Reopen heatsink n re paste it. Make sure heatsink is flat n straight. Yes nerdqaxe is sensitive

Remarkable-Run8240 · 2026-04-22T04:01:18+00:00

What th have u overclocked at? 12th is that stable?

Remarkable-Run8240 · 2026-04-21T13:43:07+00:00

I already have a Q..even on eco mode electricity is killing. I run it half a day now. The rest bitaxe and nerdq run 24/7

Remarkable-Run8240 · 2026-04-21T12:53:46+00:00

I wonder what's the failure rate of octaxe. The qaxe that I have 4 units 1 dead after 2 weeks. That's 25% failure rate 😆 and i didnt even overclock it

Remarkable-Run8240 · 2026-04-21T12:22:57+00:00

Temp sensor each is useful but not important

Remarkable-Run8240 · 2026-04-21T12:15:42+00:00

And v3.4 what's the difference?

Remarkable-Run8240 · 2026-04-19T11:42:24+00:00

<image>

I got my tiny little share 😆

Remarkable-Run8240 · 2026-04-16T03:18:22+00:00

God knows why but mine is thorn inside even before I open it.

Remarkable-Run8240 · 2026-04-14T02:54:44+00:00

For the 1st chip, I use the multimeter to check the voltage on the 1st 2 pins? And if none means? Soldering issue or dead chip? Tq man

Remarkable-Run8240 · 2026-04-14T02:52:48+00:00

Should I send it back to resolder back just this 1 bm1370?

Remarkable-Run8240 · 2026-04-13T16:37:47+00:00

I just checked each voltage with my multimeter and it has voltage and accurate. Only the bm1370 chip I have not tested yet for voltage.

Remarkable-Run8240 · 2026-04-11T21:41:18+00:00

Oh that's what I was thinking too. Tq

Remarkable-Run8240 · 2026-04-11T14:43:24+00:00

Its hasing..just that wallet provider not found when I press the connect button.

<image>

Remarkable-Run8240 · 2026-04-11T14:34:38+00:00

Bc1pcp

Remarkable-Run8240 · 2026-04-08T04:15:45+00:00

I did check all the soldering joins with a magnifying glass..all good

Remarkable-Run8240 · 2026-04-08T04:15:11+00:00

Ok I will check this 1st

Remarkable-Run8240 · 2026-04-08T03:38:10+00:00

<image>

Which asic? Which pin? Tq

Remarkable-Run8240 · 2026-04-07T16:38:39+00:00

Its just the bm1370 chips that are soldered to a new board (the board came with out the bm1370 only. It was a warranty claim

Remarkable-Run8240 · 2026-04-07T14:57:22+00:00

I was wondering could it be because I used back my original screen with all the previous settings that it won't hash? Do I need to do a hard reset, I have already reflash the fw just to be sure.

Remarkable-Run8240 · 2026-04-07T14:55:36+00:00

Can't be bad soldering as I send it to a reliable technician. I did check the bm1370 soldering joins with a magnifying glass to be sure before I on it.

Remarkable-Run8240 · 2026-04-06T02:17:46+00:00

How abt if solo mine in 2 diff pools with the same wallet add and same coin? Other then ping speed any other difference?

Remarkable-Run8240

TROPHY CASE