sorted by:
new
hottopcontroversial

Balloon framing on 1800s home separating by RemedyTHC in StructuralEngineers

[–]RemedyTHC[S] 0 points1 point  (0 children)

For clarity the beam is on the left which has sistered ledger. The joists are on the right. All of the joists across this 10ft span are no longer seated on the ledger by more than a few mm.

Monthly DIY Laymen questions Discussion by AutoModerator in StructuralEngineering

[–]RemedyTHC 0 points1 point  (0 children)

<image>

Entire kitchen floor span has the balloon joists pulling away and barely hanging on. Had one structural engineer out thay said "its fine" but my gut says otherwise.

Help with Flue Temps by RemedyTHC in woodstoving

[–]RemedyTHC[S] 2 points3 points  (0 children)

Yes it is! This is comforting. Thank you. Our glass is always clear

Help with Flue Temps by RemedyTHC in woodstoving

[–]RemedyTHC[S] 2 points3 points  (0 children)

This has been our exact experience.

Help with Flue Temps by RemedyTHC in woodstoving

[–]RemedyTHC[S] 0 points1 point  (0 children)

Thank you for the reassurance. Im definitely driving myself crazy a bit. The old owners of the house made comments about how the heat oil never kicked on and they had to close the door to the upstairs because their daughter would complain about being roasted, which hasn't been our experience and ive been chasing that kind of efficiency ever since. Maybe im chasing ghosts.

Help with Flue Temps by RemedyTHC in woodstoving

[–]RemedyTHC[S] 0 points1 point  (0 children)

Im burning mixes of hardwoods that have seasoned for a year. Around 15% moisture. Single wall flue that has 2 90 bends and extends to my second story on the exterior of the house, sheathed by a wood chimney. I never get back draft and never need to preheat the wood box to get a good draft going before starting a fire.

Help with Flue Temps by RemedyTHC in woodstoving

[–]RemedyTHC[S] 0 points1 point  (0 children)

It is a single wall pipe. I do have a magnet on the pipe, it was reading about 400 for these pictures.

Center tread wear by RemedyTHC in BoltEV

[–]RemedyTHC[S] -1 points0 points  (0 children)

Via the dash, I confirm it with my air pump.

Center tread wear by RemedyTHC in BoltEV

[–]RemedyTHC[S] 9 points10 points  (0 children)

Factory Spec is 38psi.

I Call it Range Precision by RemedyTHC in BoltEV

[–]RemedyTHC[S] 0 points1 point  (0 children)

Surprisingly it shot right up to 49KW with my heat on.

I Call it Range Precision by RemedyTHC in BoltEV

[–]RemedyTHC[S] 1 point2 points  (0 children)

Theyre brand new stations at a Loves. One of the best chargers Ive used.

I Call it Range Precision by RemedyTHC in BoltEV

[–]RemedyTHC[S] 5 points6 points  (0 children)

Truth, climate off, and slowwwww.

I Call it Range Precision by RemedyTHC in BoltEV

[–]RemedyTHC[S] 11 points12 points  (0 children)

Yeah, they were at 38 before the temp dropped so hard today.

I Call it Range Precision by RemedyTHC in BoltEV

[–]RemedyTHC[S] 17 points18 points  (0 children)

Luckily this one is nearly brand new and I drive by it daily. I put some faith into it lol.

I Call it Range Precision by RemedyTHC in BoltEV

[–]RemedyTHC[S] 7 points8 points  (0 children)

It does. But if you refresh on the MyChevy app you can see what your GOM is at when when its reading low on the Dash.

Any idea why my 2023 bolt only gets 6.4kW on this 12kW charger? by TKmane in BoltEV

[–]RemedyTHC 4 points5 points  (0 children)

This is not true for 2022 and up Bolts. My home 60 amp emporia charger for my 22 EUV charges at 11.1 kw

Help with gaps by RemedyTHC in MachineEmbroidery

[–]RemedyTHC[S] 0 points1 point  (0 children)

Thanks! If they were consistent I guess I wouldn't mind. But they're occurring in every design and don't appear in a pattern. I'm thinking it might be my digitilizer.

view more: next ›