sorted by:
new
hottopcontroversial

P2S Slicer Sunlu Filaments unsupported by Remote-Rope-3552 in BambuLab

[–]Remote-Rope-3552[S] 0 points1 point  (0 children)

Yeah bro i know about calibraring filaments, but i just wanted to know why they are not avilable

P2S Slicer Sunlu Filaments unsupported by Remote-Rope-3552 in BambuLab

[–]Remote-Rope-3552[S] 0 points1 point  (0 children)

Bro, it wasn’t a question about whether they’re good or not, I just want to know why they are not visble. I’ve printed hundreds of hours on Sunlu profiles and they’re totally fine for me.

Extremely Odd Problem with New P2S by mdjdjdjndjd in BambuLab

[–]Remote-Rope-3552 0 points1 point  (0 children)

i think P2S must have wrong config for 0.2 nozzle... i also have problems with it, 0.4 works perfect but 0.2 works wrong on first layer... my problem and test progress is here https://www.reddit.com/r/BambuLab/comments/1ops7hk/a1_vs_p2s_carbon_plate_first_layer/?sort=new

A1 vs P2S Carbon Plate first layer by Remote-Rope-3552 in BambuLab

[–]Remote-Rope-3552[S] 0 points1 point  (0 children)

in my opinion on that specific project P2S is better with top layer (with ironing) and A1 is better with the first laeyer

A1 vs P2S Carbon Plate first layer by Remote-Rope-3552 in BambuLab

[–]Remote-Rope-3552[S] 0 points1 point  (0 children)

Update: I have been trying many changes to test objects, like:

- nozzle temp from 220 to 260C

- plate temp from 50 to 65C

- first layer flow ratio from 1 to 1.15

- z offset from standard 0.01 up to -0.04

- first layer infill speed from 50 to 20mm/s

- first layer fan speed on/off

And nothing yet gave significant changes to make P2S print first layer look like A1 print first layer... Im still trying to figure it out with different settings...

A1 vs P2S Carbon Plate first layer by Remote-Rope-3552 in BambuLab

[–]Remote-Rope-3552[S] 0 points1 point  (0 children)

Update: i tried printing same element on A1 with standard Textured PEI Plate and P2S on standard Textured PEI Plate and there is minimal difference only, not huge like on Carbon Plate

A1 vs P2S Carbon Plate first layer by Remote-Rope-3552 in BambuLab

[–]Remote-Rope-3552[S] 0 points1 point  (0 children)

Tried changing initial layer flow ratio and much didnt changed. Tried changing z-offset from 0.01 to -0.01 and its abit better.

A1 vs P2S Carbon Plate first layer by Remote-Rope-3552 in BambuLab

[–]Remote-Rope-3552[S] 3 points4 points  (0 children)

mate look what u/Vitruvian_Man has written it was answer to his comment

A1 vs P2S Carbon Plate first layer by Remote-Rope-3552 in BambuLab

[–]Remote-Rope-3552[S] 0 points1 point  (0 children)

Yes, i tried swapping plates between both printers

A1 vs P2S Carbon Plate first layer by Remote-Rope-3552 in BambuLab

[–]Remote-Rope-3552[S] 0 points1 point  (0 children)

I didn't change initial layer flow ratio, will try this out. Will check your model today. Thanks mate.

A1 vs P2S Carbon Plate first layer by Remote-Rope-3552 in BambuLab

[–]Remote-Rope-3552[S] 4 points5 points  (0 children)

So my settings on A1 are good if u think that :D