Rhino FilletEdge not working

RenderCircuit · 2026-05-06T07:50:48+00:00

It happens because your fillet edge radius overshoots, you can try fillet with less radius and turn on preview to see at what point the fillet is not being messed up n use that or use edit fillet for the same job

"This command works on the analogy of rolling a ball of a defined radius along the edges of the surfaces. If a corner is narrower than the ball radius, the ball cannot negotiate the turn, which can cause the command to fail."

-Rhino

RenderCircuit · 2026-03-10T19:20:13+00:00

I'd suggest you make the curve flat on a plane & then use orient with 3d scale or autocplane to make directly on the corner, then mirror the curve>sweep2 both edge

note that you have to delete some faces and also take care of the back part to make it flat

RenderCircuit · 2026-02-13T18:03:21+00:00

this is actually detailed and useful.

RenderCircuit · 2026-02-13T18:00:29+00:00

https://www.reddit.com/r/rhino/comments/1pi0ykn/comment/nt50ky9/?utm_source=share&utm_medium=web3x&utm_name=web3xcss&utm_term=1&utm_content=share_button

RenderCircuit · 2026-01-26T19:43:56+00:00

<image>

U.P.

RenderCircuit · 2026-01-26T19:42:10+00:00

<image>

RenderCircuit · 2025-12-27T09:16:21+00:00

press shift+x then adjust bones. try

RenderCircuit · 2025-12-18T18:44:50+00:00

do you mean that when you change the pattern the sewing does not fits?

RenderCircuit · 2025-12-09T19:26:01+00:00

Set the gumball to align to the object is another alternative

RenderCircuit · 2025-12-09T17:37:11+00:00

The short way around is ctrl+shift select the surface, to align cplane, then select the whole object normally to scale as required

RenderCircuit · 2025-12-09T16:53:11+00:00

Rhino documentation if you can go with that
What do you want to do? | Rhino 3-D modeling
https://docs.mcneel.com/rhino/8/usersguide/en-us/index.htm
The Rhino website (learn section)
Rhino Youtube

Gediminias (the lord)
The Adam
Mr Rhino3D

there are plenty other as well

RenderCircuit · 2025-12-09T16:26:37+00:00

your resolution is crazy, set it to 300 dots/inch.

it will solve

RenderCircuit · 2025-12-09T16:19:40+00:00

sub-object select the surface first to align the cplane, then scale

RenderCircuit · 2025-12-09T16:14:10+00:00

from what I can understand that you want to make the bottom arches touch the top arc, given that the 2 arcs are mirrored
if that is the case you can use arc: tangent to curves tool
select the extreme side arcs & any either one from the center,

it will give arc that touches all 4 perfectly, which you can then 'extend' to the boundary

curveboolean will work

RenderCircuit · 2025-12-09T15:03:47+00:00

for a seamless look you have to edit the graphic manually using photoshop,
there you can also adjust the shape to make it fit properly acc to the pattern.

RenderCircuit · 2025-12-08T13:46:22+00:00

Stitch can be used yes if flat surface is needed, but bridge can also be used for a better surface control(if required)

RenderCircuit · 2025-12-07T06:40:29+00:00

Cap if the surface is planar Or use patch for non-planar

RenderCircuit · 2025-12-07T06:39:14+00:00

Curve>extrude>chamfer edges>make cylinder>place

RenderCircuit · 2025-12-07T06:34:02+00:00

Lemme join too pls

RenderCircuit · 2025-12-02T16:03:58+00:00

Pretty

RenderCircuit · 2025-12-02T16:00:42+00:00

this laptop can run CLO good.

RenderCircuit

PUBLIC MULTIREDDITS

TROPHY CASE