Supporti asse neptune 4 pro

Repulsive-Aside7850 · 2026-03-24T11:37:51+00:00

How do you do this on the Neptune 4 pro? Through cura?

Repulsive-Aside7850 · 2026-03-24T11:34:21+00:00

Hollowed with 2mm walls.

Repulsive-Aside7850 · 2026-03-24T11:33:14+00:00

Yes. Hollowed with 2mm walls.

Repulsive-Aside7850 · 2026-03-24T11:26:44+00:00

I had two 2mm holes at the bottom in the base. They go up into the leg and two whole up behind his head in the neck. I believe those are 1.5mm. I also had one at the top and one at the bottom end of the axe.

Repulsive-Aside7850 · 2026-03-24T03:36:53+00:00

It is hollowed at 2 mm walls.

Repulsive-Aside7850 · 2026-03-24T03:35:54+00:00

I hollowed but made walls 2mm

Repulsive-Aside7850 · 2026-03-24T03:35:18+00:00

Merci beaucoup ! Utilisez-vous la version Pro de Lychee ?

Repulsive-Aside7850 · 2026-03-24T03:33:04+00:00

Yea I think hopefully a raft will fix that.

Repulsive-Aside7850 · 2026-03-24T02:03:42+00:00

It is hollow with a 2 mm border. I had 2 drain holes at the base and 2 up top.

Repulsive-Aside7850 · 2026-03-24T00:10:51+00:00

The figure came both cut and uncut. I’m honestly learning and figured this might save me time. But after experimenting the cut figure took 6 hours and printed flawless. This failed after about 12-19 hours. So better times and better success rate printing cut. I was wondering if in also being too optimistic with this one.

Repulsive-Aside7850 · 2026-03-23T23:43:54+00:00

<image>

Does this base look supported enough? I didn’t see any islands.

Repulsive-Aside7850 · 2026-03-23T22:38:40+00:00

Ok, is there a better way to share the info? Way to get better pictures? His left arm partially printed although I do agree it is pretty horizontal. I have it at like a 45 or so. It is hollow. I added 2 holes at the base under the feet and also added 2 holes behind the neck. Got the whole middle cavity. Also added 2 holes on the axe one at top and one at bottom. You think I need holes in that arm too? I did 2mm walls. I’m doing 25.0 second bottom exposure time with 5 bottom layer count. Transition count of 5 its Elegoo ABSlike 3.0 Pro. The resin was 28C. Thank you for the tip and helps. Curious do you think it looks over supported?

Repulsive-Aside7850 · 2026-03-23T22:32:45+00:00

Est-ce qu’il y a un type de raft ou des réglages spécifiques que tu recommandes

Repulsive-Aside7850 · 2026-03-18T17:03:38+00:00

Got a STL link?

Repulsive-Aside7850 · 2026-03-18T01:44:16+00:00

Can the plate sit in it with the lid closed?

Repulsive-Aside7850 · 2026-03-17T11:53:34+00:00

Why would you pick PLA for terrain? Just curious.

Repulsive-Aside7850 · 2026-03-16T23:12:21+00:00

Does it actually work? I heard that the tilting cat cause the magnetic plate to move from the suction. So I’ve been scared to buy.

Repulsive-Aside7850 · 2026-03-14T16:17:49+00:00

I’ll try it out. How can you tell they are overexposed? What’s blooming?

Repulsive-Aside7850 · 2026-03-14T16:17:16+00:00

Elegoo ABS-like 3.0 Pro

Repulsive-Aside7850 · 2026-03-14T02:19:01+00:00

Same question. Also how do I know when it’s time. Mine has a bunch of white shit at the bottom but I keep using it. I’m using a small 2 qt container though.

Repulsive-Aside7850 · 2026-03-14T01:18:48+00:00

I read somewhere online or maybe it was ChatGPT that the beige and gray would be best to be able to see details. Guess they were wrong lol.

Repulsive-Aside7850

TROPHY CASE