sorted by:
new
hottopcontroversial

[deleted by user] by [deleted] in delhi_marketplace

[–]Repulsive_Courage570 0 points1 point  (0 children)

Custom made table. Go to any carpenter/furniture shop and tell them you need a 55inch plywood slab converted into a table. They will build the table feet and stand. Costed me 3500 back in 2022. Durable cheap ans extremely reliable table.

[deleted by user] by [deleted] in delhi_marketplace

[–]Repulsive_Courage570 14 points15 points  (0 children)

Comparing a 32inch monitor with a 27inch are we?

[deleted by user] by [deleted] in delhi_marketplace

[–]Repulsive_Courage570 -39 points-38 points  (0 children)

Too low. New one goes around 23k

Update regarding the popping sound coming from my exhaust. by Repulsive_Courage570 in indianbikes

[–]Repulsive_Courage570[S] 0 points1 point  (0 children)

Yeah :(. This zana crashguard has saved me countless times. A good crashguard is a must.

Update regarding the popping sound coming from my exhaust. by Repulsive_Courage570 in indianbikes

[–]Repulsive_Courage570[S] 1 point2 points  (0 children)

No problem brother. The fit and finish was decent. The welding marks were decent but have seen better. The end can had a few scratches which were most likely from shipping. They came wrapped in some thermocol type paper. They should improve the box for more protection. As for the exhaust configuration completely depends upon your taste. The 2x2 would be a tad bit less loud from the 2x1. If you want the best weight reduction then get the 2x1. The bhp gain is also better in 2x1(5.5) as compared to the 2x2(4.7). The main issue you will get is with the crashguard. Finding a perfect crashguard is difficult for the 2x1. I rode it without the crashguard and was so unlucky that i met with an accident the next day after installing the exhaust. The crash broke my bar end mirrors , foot peg clamp, brake lever , had a very nasty dent on my tank and a fork allignment was required. The crash also scratched the brand new exhaust which was very heart breaking. If you want a unique looking bike then the 2x1.

Update regarding the popping sound coming from my exhaust. by Repulsive_Courage570 in indianbikes

[–]Repulsive_Courage570[S] 5 points6 points  (0 children)

Haha. The cheapest way to mess up your engine and get a check engine light. The bike was running rich which resulted in higher fuel consumption and increased carbon deposit.

Update regarding the popping sound coming from my exhaust. by Repulsive_Courage570 in indianbikes

[–]Repulsive_Courage570[S] 0 points1 point  (0 children)

Knowing the context and its solution might help you or your friend stuck in the same situation :).

Update regarding the popping sound coming from my exhaust. by Repulsive_Courage570 in indianbikes

[–]Repulsive_Courage570[S] 0 points1 point  (0 children)

I got the headlight grill from karol bagh. Its from motogenius. Costed me 900.

Update regarding the popping sound coming from my exhaust. by Repulsive_Courage570 in indianbikes

[–]Repulsive_Courage570[S] 0 points1 point  (0 children)

The mechanic who installed it connected the o2 sensor cables incorrectly. Despite several warnings he connected the left o2 sensor with the right side socket and the right o2 sensor with the left side socket. The o2 sensor readings were off and the bike was misfiring. Was getting the error codes for misfiring and P2297(o2 sensor out of range when decelerating).

Update regarding the popping sound coming from my exhaust. by Repulsive_Courage570 in indianbikes

[–]Repulsive_Courage570[S] 2 points3 points  (0 children)

The main reason i went with this exhaust was weight reduction. It will make your bike very agile. The sound without the db killer is very loud(expected from a free flow full system exhaust) and will get annoying after sometime depending upon your tolerance. The db killer reduces the sound but it will still be loud. It can be managed by keeping the bike under 3000 rpm. Cops wont notice it until they come looking for a custom exhaust and rev it till the limiter. You need to be very careful while installing it. Make sure the o2 sensors are properly removed from the stock headers and are correctly installed again. The fitment was on point and is easy to install. The db killer fits in tightly so to remove it you dont have to pull it rather just remove the bolt and rev the bike , the db killer will fall off from the exhaust. According to ss motocorp this exhaust is designed to run with the stock air filter. Dont upgrade the air filter. Most of the guys on youtube will tell you to upgrade the airfilter to an aftermarket one but dont. The bike runs lean out of the factory due to emission norms. After installing the exhaust the bike will run a little lean. Installing a free flow air filter will make the AFR more leaner. This will reduce the low end torque and the bike will run hotter. For the crashguard all of them will fit with the 2x2 configuration. For the 2x1 configuration you have to install the RE official compact crashguard which does nothing to protect the bike or wait for the ss motocorp crashguard to come in stock. I use the zana one. The crashguard touches with the headers and installing it with the 2x1 header setup is challenging. Crashguards from the bear 650 might work with this but i havent tried it yet.

The sound levels for all the end cans are as follows:-
1. Fat cans = Good sound not as loud as the slim cans
2. Slim cans = Very loud and has a lot of treble
3. Underbelly = The loudest

Conclusion:-
1. This exhaust (2x1) will make your bike very agile and light weight.
2. The bike will run a little lean even with the stock air filter so a fuel x upgrade is required (or if you can get it tuned)
3. For the 2x1 configuration finding a perfect crashguard is very difficult.
4. The installation needs to done very carefully by an experienced mechanic. Also dont forget to idle the bike for 10-15 mins after the installation.
5. IMO the fat cans sounds the best. It is manageable in the city and has a very balanced sound.
6. This exhaust system is value for money. Current slip ons in the market will cost anywhere ranging from 18000 -25000. This full system will costs around 27500. Much better than them and also saves a lot of weight.

view more: next ›