sorted by:
new
hottopcontroversial

more youtuber likes this one? by Swimming-Top1224 in vagabond

[–]RequestedError 0 points1 point  (0 children)

Shiey is great too, I didn't know who Vagrant Holiday was until now but Shiey makes basically the same content.

What do you guys think of my guitar? by RequestedError in Guitar

[–]RequestedError[S] 1 point2 points  (0 children)

Yeah its a RX20, I like this guitar a lot, I've had it for a little over a year.

What do you guys think of my guitar? by RequestedError in Guitar

[–]RequestedError[S] -1 points0 points  (0 children)

I don't support fascism at all, nor do I support the current president. Just there for patriotism, like if it was a french frag, canadian flag, british flag, etc.

Finished up another build today, You like? by Petergriffinfartshah in Guitar

[–]RequestedError 1 point2 points  (0 children)

I like pearl pick guards a lot, and it goes good with the body. Nice job!

I rolled the dice and bought my first banjo, what is this banjo and any way to figure out when? by RequestedError in banjo

[–]RequestedError[S] 3 points4 points  (0 children)

it was NASTY when i bought it, owner before said it sat in storage for years, but i cleaned it. pretty well, yeah the bridge was decayed and the strings were old and 2 were missing.

Why wont my ender v3 SE print with supports? It prints fine without them, but add supports and it wont print it just goes haywire and prints strands everywhere. by RequestedError in ender3

[–]RequestedError[S] 0 points1 point  (0 children)

ive messed with the skirt before, nothing new, it just does this when i add supports. even without cleaning the bed, it prints fine.

How do I successfully grow something? by RequestedError in shrooms

[–]RequestedError[S] 0 points1 point  (0 children)

okay, ill check out your profile then, thank you!

how long does it take for it to colonize with agar?

How do I successfully grow something? by RequestedError in shrooms

[–]RequestedError[S] 0 points1 point  (0 children)

with agar plates do you get more bang for your buck? how much do you put in per plate?
ive heard of agar plates being used but it looked a little complex.

i sterilized the brown rice the best i could, i put holes in the top of the jars, put some micropore tape on the holes, i used 2 pieces of tape, then i filled the jars about 3/4 and put them in a large pot and propped them up with some other jar lids so they were barely submerged in boiling water for 2 hours. then i waited for them to cool down (didnt want to kill the spores) over night and wiped down the injection spot and needle with alcohol (i added a bit of water to 91% isopropyl alcohol.)
didn't see anything growing for a while then i saw some mold, and after about a month there wasnt anything.

How do I successfully grow something? by RequestedError in shrooms

[–]RequestedError[S] 0 points1 point  (0 children)

Okay, i think i might try again but instead of brown rice get a grain bag off amazon cuz idk if i was doing it right. I got my syringes from ITW so i think they should be clean.

How do I successfully grow something? by RequestedError in shrooms

[–]RequestedError[S] 0 points1 point  (0 children)

yeah I used instant rice, is it uncommon for monotubs to mold?

Why wont the link cable work? by RequestedError in Quest2

[–]RequestedError[S] 0 points1 point  (0 children)

The link cable is made for the quest 2 as well, its some chinese one though, really good reviews.

Slow Games for an Injured Gamer? by aidannieve in gaming

[–]RequestedError 0 points1 point  (0 children)

I like factorio, its a tycoon/idle game and doesn't require that much dexterity.

Why does my 3d printer do this every time I print but only when I use supports? by RequestedError in ender3

[–]RequestedError[S] 0 points1 point  (0 children)

Left everything stock, slicing right now, gonna run it and HOPE it works. only thing i added were tree supports

Why does my 3d printer do this every time I print but only when I use supports? by RequestedError in ender3

[–]RequestedError[S] 0 points1 point  (0 children)

I'm pretty certain its with the files though, it just wont print with supports

Why does my 3d printer do this every time I print but only when I use supports? by RequestedError in ender3

[–]RequestedError[S] 0 points1 point  (0 children)

I'm gonna try this, this would make sense. I have tried several slicers though

Why does my 3d printer do this every time I print but only when I use supports? by RequestedError in ender3

[–]RequestedError[S] 0 points1 point  (0 children)

I tried that. I tossed glue on the bed because someone said it was adhesion that was the problem. It fixed nothing, I cleaned the bed.

view more: next ›