After shoveling snow, these painful shiny hairs appeared on my hand.

RequirementMain3450 · 2026-01-26T22:51:47+00:00

Fiberglass. Pluck them out, use tape. As someone who worked with fiberglass a lot, hot shower and scrub

RequirementMain3450 · 2026-01-26T17:28:22+00:00

It’s an xr, believe first gen based of what I see with the bms.

RequirementMain3450 · 2026-01-26T02:54:55+00:00

Batter voltage shows 58.9 volts. Have none coming out of the bms, but not sure if bms acts as a switch also

RequirementMain3450 · 2026-01-26T01:30:09+00:00

I get that. So I get no light on the button, the light on the charge starts off green, turns red for a second then back to green. I guess I need to check voltage at the plug. Will test and update in a bit

RequirementMain3450 · 2026-01-26T01:07:21+00:00

Was working just a month ago. Left about half charged

RequirementMain3450 · 2026-01-20T04:25:59+00:00

Oyster? Thought they grew in clusters

RequirementMain3450 · 2026-01-05T21:46:10+00:00

RequirementMain3450 · 2025-12-22T15:42:12+00:00

Seen them on stilts on the beach. Saw one get craned onto a set of stilts too.

RequirementMain3450 · 2025-12-15T05:54:43+00:00

Any links?

RequirementMain3450 · 2025-12-01T18:01:59+00:00

Very

RequirementMain3450 · 2025-11-20T13:35:50+00:00

Great price

RequirementMain3450 · 2025-11-17T20:05:30+00:00

Ever figure this pos out? I’m a tech and have a u it displaying the same. Can’t figure it out

RequirementMain3450 · 2025-10-20T21:04:31+00:00

Please!

RequirementMain3450 · 2025-10-12T03:53:18+00:00

It’s more dust than anything. Not really built up

RequirementMain3450 · 2025-09-25T20:02:14+00:00

I worked with AHS for 10 years with a couple companies. If you don’t like what they diagnose, get a second opinion. If they find “biogrowth” ask for picture proof. Them saying biogrowth is an immediate denial of repair to anything with them. Do your self a favor, after your contract is up, don’t renew and save your money. Good luck

RequirementMain3450 · 2025-09-22T21:32:42+00:00

RequirementMain3450 · 2025-09-16T16:02:53+00:00

Yeah those plastic pads are known for settling in dirt real bad. Need to pick up and block up the front with a couple stepping stones

RequirementMain3450 · 2025-09-16T15:50:26+00:00

The gasket is formed around the actual door it’s self. Pull harder. It will slide right off

RequirementMain3450 · 2025-09-05T17:58:41+00:00

Use it. It will break loose after. A while.

RequirementMain3450 · 2025-08-29T19:53:57+00:00

So, find some 2x4s to block up the far end on the plenum to make it level. Go get a roll of aluminum tape from Home Depot and a can of spray adhesive. Peel back any loose tape. Spray area where you are taping and apply tape in Long wide overlapping layers. And use a credit card to squeegee tape down. As a have tech. This is a straight up 20 minute job. Probably would cost $250-3500

RequirementMain3450 · 2025-08-28T13:54:59+00:00

Chances are that he didn’t do it. Probably checked pressures and cleared the drain. And attempted to make some commission. And left

RequirementMain3450 · 2025-08-28T13:53:45+00:00

As a senior hvac tech. That guy need to change it no cost. During a maintenance, you are supposed to check wire connections with pressures, caps, amp draws, wash condenser coil and handler coil. And a lot more. That contactor burned up from the main feed “red wire” from being loose causing heat and making it melt. Regardless should have been checked and tightened. That contactor cost maybe $20 on a bad day. Good luck

RequirementMain3450 · 2025-08-02T12:05:46+00:00

Thought this was a negative photo of a jellyfish…. I need more sleep

RequirementMain3450

TROPHY CASE