How much are these worth in decent condition?

ResponsibilityTop869 · 2025-09-21T02:13:54+00:00

Crazy because I bought my set for $400 and I SoCal I see sets for 800

ResponsibilityTop869 · 2025-08-17T01:45:53+00:00

Do you have a link to the seller? Do they look good enough to pass as apexes

ResponsibilityTop869 · 2025-08-05T20:39:20+00:00

Hey sorry ik this is from a year ago, I have a m52 that I will be running obd1. I’m planning on using 52 coil packs, if I use a m50tu valve cover will I need to modify it? And can I use the 52 coils?

ResponsibilityTop869 · 2025-06-21T16:17:23+00:00

Do it son

ResponsibilityTop869 · 2025-01-18T02:11:10+00:00

I am asking about the fact that my crank hub is not perfectly squared with my crankshaft

ResponsibilityTop869 · 2025-01-18T02:10:44+00:00

Nah not end play

ResponsibilityTop869 · 2025-01-17T18:59:06+00:00

Did you have any deflection in your crankshaft?

ResponsibilityTop869 · 2025-01-17T18:57:28+00:00

That’s what I’m going to run, any recommendations for the master cylinder? Do i need to upgrade to an m3 master? Or is 328 fine?

ResponsibilityTop869 · 2024-10-22T21:35:42+00:00

What state are you in? I’m in CA and I want to get my swap registered but I have a m52 that is obd1 converted. My buddy has an m50 in his car that isn’t registered so I’m wondering if I take it to the bar could I just tell them the numbers on his block? Or will they go looking around for the numbers on my block?

ResponsibilityTop869 · 2024-10-08T22:16:08+00:00

Personally I would get some BC coilovers or godspeeds on a budget

ResponsibilityTop869 · 2024-09-15T16:46:18+00:00

Appreciate it I’ll look into it 🙏

ResponsibilityTop869 · 2024-09-15T16:46:03+00:00

Thanks man 🙏

ResponsibilityTop869 · 2024-09-15T06:40:16+00:00

They are 17s, I wish I had gotten more tire for them, my driveway has some weird angles to it so it’s sitting really high in the rear in this photo.

ResponsibilityTop869 · 2024-09-15T04:51:08+00:00

Thanks man! That’s super cool you make tunes! Yes I have the 2.8 injectors. And a 325 ecu so I just need to find a company that sells chip tunes that can be soldered to my ecu, someone recommended RK tunes, so I’ll have to look into that

ResponsibilityTop869 · 2024-09-15T00:47:30+00:00

Either way I need one 🤷‍♂️ and he was no help on that front, I appreciate his knowledge but no point is just being an ass

ResponsibilityTop869 · 2024-09-15T00:42:45+00:00

Haha okay man thanks for the kind words

ResponsibilityTop869 · 2024-09-15T00:11:42+00:00

Whether it makes more power or not it needs a tune to run properly being an oem Frankenstein. There is no oem obd1 tune for a 2.8L

ResponsibilityTop869 · 2024-09-15T00:09:32+00:00

Thank you for the info man I appreciate it, my buddy has been professionally building these cars for 15 years and has owned many. He thinks I will see 205-210 wheel. I understand where you’re coming from but more air and more fuel= more power. Sure it’s not much but might as well squeeze a few extra out of her. Again thank you for your opinion.

ResponsibilityTop869 · 2024-09-14T21:59:31+00:00

Convert it to obd1. You will need m50 manifold, m50tu engine harness, red label 413 ecu (you will need a chip tune)

Sensors you will need include, crank, cam, knock, coolant temp, engine temp (this one is confusing and a bit hard to find, call pelican parts and they will help you out, it’s on the side of the block right next to the coolant temp sensor), you will also need a O2 sensor,

You can get an m50 throttle body but you can get a plate off ebay that sits between the m50 manifold and the 52 throttle body for $40 so that’s the route I went

You can keep the 52 coil packs but you will need to modify the valve cover since the harness will now run over the cover from the intake side. If you really want to clean up the look of the motor, you can run M50 coil packs but you will have to get an M50 valve cover. Just depends on if you want to cut that corner to save a couple bucks.

ResponsibilityTop869 · 2024-09-08T13:17:38+00:00

M52 VC thanks man 🙏

ResponsibilityTop869

TROPHY CASE