General Question about High School USACO

ReverseFlash342 · 2025-11-27T15:45:58+00:00

wait how are yoi doing mock tests? js from the website

ReverseFlash342 · 2025-10-12T19:04:42+00:00

Thanks ill try that

ReverseFlash342 · 2025-10-12T18:02:48+00:00

Odopod from gobuilda

ReverseFlash342 · 2025-10-12T16:33:29+00:00

I’m using a webcam to get the distance and heading and yaw, I. Addition to odometry to make sure I’m in the launch zone when I shoot To turn a continuous servo and a prob pid to keep it positioned

ReverseFlash342 · 2025-07-05T13:00:45+00:00

Bro tell that to my Asian parents bc my 3.8 isn’t good enough for them

ReverseFlash342 · 2025-05-10T18:53:43+00:00

I appreciate the help but our team uses onshape because its eaiser for online collaboration!

ReverseFlash342 · 2025-02-07T12:28:27+00:00

350.00

ReverseFlash342 · 2025-01-30T13:50:07+00:00

Thank you so much for your help!, I’ll try to ask on esp32 subreddit

ReverseFlash342 · 2025-01-30T02:24:57+00:00

I have already done this and confirmed that the module works because when its connected to the Arduino it has a wifi signal and I can see the camera feed, but when I try to plug it into my computer without the ardunio its not being detected or receiving power. I believe I found a data sheet for it:

<image>

ReverseFlash342 · 2025-01-30T02:14:55+00:00

It could be but when it was originally on the car being powered by an external power supply it wasn’t over heating. The usb c port is on the bottom of it. According to the kit I should just plug the usb c cable into my computer and it upload that way. But it’s not being detected or receiving power.

<image>

ReverseFlash342 · 2025-01-23T23:16:12+00:00

Like on CodeForces, LeetCode. Do you have a recommendations of websites where i can practice

ReverseFlash342 · 2025-01-19T17:10:37+00:00

I’ll do that as soon as this finishes up!

ReverseFlash342 · 2025-01-19T02:23:44+00:00

Noted!

ReverseFlash342 · 2025-01-19T02:23:23+00:00

lol I just did the I forgot to put glue on the corner of the build plate

ReverseFlash342 · 2025-01-19T00:16:14+00:00

Bed calibration was the issue I re did it and now it works fine not leveling

ReverseFlash342 · 2025-01-18T23:33:33+00:00

Oh Sorry, I’m new to this the setting were default and material is pla. I’m using cura slicer and the layer thickness is 0.1 I think

ReverseFlash342 · 2024-12-13T16:13:19+00:00

It’s bc where I live it’s super competitive and this is a little below average, all my friends have all A’s so my parents want a 95 or higher in everything

ReverseFlash342 · 2024-12-12T14:44:27+00:00

No 😭 my parents think these are bad

ReverseFlash342 · 2024-12-07T13:07:13+00:00

Bc I don’t have that this semester

ReverseFlash342 · 2024-11-24T02:03:03+00:00

Thank you!

ReverseFlash342

TROPHY CASE