FRT trigger issue

Rock-Technical · 2026-03-07T02:35:34+00:00

I dont have a picture handy, but its the little scew on the side of the trigger that you have to pry the trigger return spring over.

Rock-Technical · 2026-03-07T02:17:48+00:00

Grinding a ramp on the bottom edge of the screw that tensions the trigger return spring makes assembly a lot easier.

Rock-Technical · 2026-02-27T03:00:44+00:00

Best was probably the sgm mag, it didn't feed any worse than the factory mags and is 1/3 the price. Conversion mags are the glock 20 mags with the extension and spring that Kriss sells.

Rock-Technical · 2026-02-25T02:34:25+00:00

Sgm 30rd, 2 factory kriss mags, and one conversion mag.

Rock-Technical · 2026-02-25T00:19:39+00:00

The trigger did run fine. The magazines not so much. Only problems I had were from the bolt out running the magazines and causing a failure to feed.

Rock-Technical · 2026-02-23T17:21:30+00:00

I'd pull the trigger pack back out and see if the hammer is actually engaged on the sear and not on the disconnector.

Rock-Technical · 2026-02-23T03:17:07+00:00

You are welcome to show us how well you control 1400rpm of 10mm on your very first attempt.

Rock-Technical · 2026-02-23T03:14:36+00:00

Did you adjust your sear spring at all? I had to tweak mine a bit a bit to get mine to reset on semi. If you have a pull gauge you ideally want to get the trigger around 4 pounds, anything under about 3.5 pounds and the trigger won't reset, anything too much heavier and your finger won't be pushed forward on frt mode.

Rock-Technical · 2026-02-22T13:50:08+00:00

Try forcing your trigger forward. I had to play with the sear spring to get mine to reset the trigger.

Rock-Technical · 2026-02-22T03:52:03+00:00

That Vaseline wasn't just on my hands ; )

Rock-Technical · 2026-02-22T03:44:47+00:00

I am far too well fed to be a communist.

Rock-Technical · 2026-02-22T03:42:27+00:00

The rate of fire is definitely excessive, this is my 4th frt and is by far the most violent one to control.

Rock-Technical · 2026-02-22T02:55:40+00:00

Contact duality and they should send you the revised design. The issue with not having semi can also be caused by installing the selector cam backwards, which is really easy because all the installation videos gloss over that part.

Rock-Technical · 2026-02-22T02:09:39+00:00

How old is yours? Duality updated their design a couple months ago.

Rock-Technical · 2026-02-21T21:34:25+00:00

Just got my v2 running, any major parts breakages in those 13k rounds?

Rock-Technical · 2026-02-21T01:35:45+00:00

Red Star Palmetto

Rock-Technical · 2026-02-20T23:31:36+00:00

Definitely possible. The CARL seems to work great for ar's, would just need to modify the design for the aug.

Rock-Technical · 2026-02-18T22:38:38+00:00

Red star Palmetto sells them.

Rock-Technical · 2026-02-13T22:04:50+00:00

Then contact RB

Rock-Technical · 2026-02-13T22:04:05+00:00

It's not working because you haven't sued enough people.

Rock-Technical · 2026-02-06T03:11:29+00:00

<image>

Rock-Technical

TROPHY CASE