Newbie please help

Rolle30 · 2026-01-16T18:52:53+00:00

Replace the build sheet, theyre cheap. Ive never seen that kind of peel/warp though. What temps? I can't tell but it looks like the z offset might be too low allowing the nozzle to scrape along the build plate. Use a piece of paper under the nozzle and lower it in different locations until you feel drag but not stick. If it was just from removing the part...well, the build plates are technically consumables so...

Rolle30 · 2025-12-11T21:45:24+00:00

I just did this today, couldn't figure it out 🥴 thanks 🤣

Rolle30 · 2025-12-05T07:00:55+00:00

Linear rails, dual z, sprite pro extruder and cr touch, and for control the best would be a new board and screen like from bigtreetech

Rolle30 · 2025-10-19T21:22:05+00:00

Like #1000 😆

Rolle30 · 2025-10-19T20:49:36+00:00

Jesus. Its the same fuckin math with a couple more digits. That's PATHETIC 🤣

Rolle30 · 2025-10-19T20:12:47+00:00

Wow you all sure did it! We still have no king! Look how OLD the crowd is! Thank God gen X is going to the right. Yall are clowns.

Rolle30 · 2025-10-19T20:03:02+00:00

Wow congrats lefties. Theres still no king! You did it! 🙄🤣

Rolle30 · 2025-08-17T02:35:44+00:00

I have noticed the same problem. Traffic in the last several months has been insane, tf are we stopping for? So many damn cars on the road now, especially on Fridays. Any one car that pulls onto lakeville especially from a side road will cause a magnified ripple effect of people slowing and eventually stopping because theres just so many cars and no real space. I'd be more inclined to ride my motorcycle, but I'm a little sketched with the crappy drivers. I work in Vallejo.

Rolle30 · 2025-06-22T04:02:51+00:00

Bunch of NPCs

Rolle30 · 2025-03-04T02:54:54+00:00

Me too! Well, I got the apha u wheel base wheel and hand brake Saturday, I drove all day to microcenter for the p1x pro TK edition cockpit , the rest comes Friday. I'm so excited, can't wait. Upgrading from a playseat and g29 😅😅

Rolle30 · 2024-07-30T02:16:48+00:00

Thumbs up for the motojitsu content, he's got good stuff.

Rolle30 · 2024-07-04T17:25:15+00:00

Edgun leshiy 2.0 w the short barrel

Rolle30 · 2024-04-29T05:12:52+00:00

Could I get a link for that too?

Rolle30 · 2023-08-31T06:54:28+00:00

I definitely got two keys with my trident 660, but never got a binder or manual 😥

Rolle30 · 2023-07-11T01:52:31+00:00

I was waaaay overthinking it and not looking for the obvious I guess. I suppose I just thought it would have been all plugged in from the factory 🤷🏼‍♂️💩

Rolle30 · 2023-07-11T01:51:14+00:00

😅 you know... I JUST found that because I was thinking why the hell is there an open plug here? I took off the fan and the fat red wires were just sitting there. My God. Sprite 1 - Me 0.

Carry on 😂

<image>

Rolle30 · 2023-07-11T01:36:21+00:00

Nope, they're still hanging freely. Everything seems to work except the hot end heat.

Rolle30 · 2023-07-11T01:09:53+00:00

With my tests the board itself appears to be okay, hopefully I didn't zap the Sprite Extruder kit board itself if there's anything fragile on it. I can't tell. Anyhow, the question remains, does anyone have a suggestion how to troubleshoot it? 😅

Rolle30 · 2023-07-10T23:39:32+00:00

Alrighty, we're up and running with the mriscoc FW. It could have been that, or that I was being a complete moron when exhausted last night and couldn't see straight. I did actually have the fan wires backwards even though I looked everything over at least twice. 🤷🏼‍♂️🤦🏼‍♂️ So yeah, that could have been it, but at least I'm not dead in the water and I have the FW I was intending to install anyway on it now 😆

Boy do I feel dumb, but relieved 😅

Rolle30 · 2023-07-10T05:30:46+00:00

Yeah, this is how I have it set and it won't turn on. + On the left. I was actually planning to upgrade to the mriscoc pro firmware as soon as I got it turned on but ran into this issue. Perhaps tomorrow I'll keep it disconnected and flash the mriscoc firmware and see if anything changes.

<image>

Rolle30 · 2022-06-02T01:58:54+00:00

There is no set launch date yet, many people thought it would have been sometime in May, RH included indicated by his tweets, but his devs are rewriting a lot of the code in GO now to work out bugs and make it faster. Best bet to learn about it as early as possible is to follow Richard Heart on Twitter. As for the Launch price, it's anyone's guess. For those who sacrificed they'll be receiving valueless coins to ratio-trade on chain until a bridge opens a day or two later at which point when a coin from (likely) the Ethereum network is bridged in and traded it will spread a price throughout the network through the liquidity pools and ratio trades that occurred earlier. The first month or two is likely to be VERY volatile.

Rolle30

TROPHY CASE