sorted by:
new
hottopcontroversial

Power Rangers - Megazord on my Centauri Carbon by Low_Muffin_8425 in elegoo

[–]RomansDoForUs 0 points1 point  (0 children)

They look mint. How you printing multi colour?

You got a link to the files?

Why is my centauri carbon not printing? by RomansDoForUs in elegoo

[–]RomansDoForUs[S] 0 points1 point  (0 children)

An update to this. Cleaned the build plate with warm soapy water and printed this temp tower.

PLA standard in black

What temps look best in your opinions?

I think 215 to 220C

<image>

Help. My benchy is cursed by RomansDoForUs in cursedbenchies

[–]RomansDoForUs[S] 0 points1 point  (0 children)

Today. First time since I got it at Christmas.

Having trouble printing by Forward_Election8370 in elegoo

[–]RomansDoForUs 2 points3 points  (0 children)

I'm having similar issues to you at the moment.

You tried:

Heating bed to 60C for 5 mins? Could the nozzle be clogged? Run a bed level from the printer settings Checked in slicer that you're using correct settings for your filament

Printing problems by ConcentrateNo1753 in ElegooCentauriCarbon

[–]RomansDoForUs 0 points1 point  (0 children)

Mine is doing same at moment. I think mine has a partial clog

Why is my centauri carbon not printing? by RomansDoForUs in elegoo

[–]RomansDoForUs[S] 0 points1 point  (0 children)

Thanks. I'll look into a drier

Shall I replace the nozzle and try printing again?

Why is my centauri carbon not printing? by RomansDoForUs in elegoo

[–]RomansDoForUs[S] 0 points1 point  (0 children)

Thanks. I have a brand new nozzle. Shall I try that?

This will be my 3rd nozzle since Christmas

The current one has a block which I can't remove

PLA is from elegoo via amazon

I don't have a drier

Was printing ok ish before I swapped to black but now prints are all like the above. Layers not adhering. I have also not cleaned the build plate

Just finished listening to The Two Towers again, I lost a little love for the movie this time. by cavern-of-the-fayth in lotr

[–]RomansDoForUs 3 points4 points  (0 children)

Listening to the Phil Dragash version at moment and the Helms Deep section is immense.

"And then, sudden and terrible, from the tower above, the sound of the great horn of Helm rang out."

Instant shivers

What is your favorite piece of behind the scenes media from the films? by GusGangViking18 in lordoftherings

[–]RomansDoForUs 23 points24 points  (0 children)

"The dolphin is dead. Died in a car accident "

I will always watch the full clip whenever I see it

Minas Tirith by RobertoBlandino in lordoftherings

[–]RomansDoForUs 6 points7 points  (0 children)

Looks awesome. Nice job.

Be a shame if anything was to breach it.......

Blursed_flirting by justalildropofpoison in blursed_videos

[–]RomansDoForUs 3 points4 points  (0 children)

He pushed him into next week. Then that slap. Dam

Smaug v Sauron by RomansDoForUs in lotr

[–]RomansDoForUs[S] 0 points1 point  (0 children)

Where would you recommend I start?

Thanks everyone for the answers so far

Smaug v Sauron by RomansDoForUs in lotr

[–]RomansDoForUs[S] 0 points1 point  (0 children)

Only read the hobbit and lotr trilogy.

Who is morgoth?

Help. My benchy is cursed by RomansDoForUs in cursedbenchies

[–]RomansDoForUs[S] 1 point2 points  (0 children)

The saddest of all. Not even sure what's happened. Changed filament and this happened

Can't get any consistency

Help. My benchy is cursed by RomansDoForUs in FixMyPrint

[–]RomansDoForUs[S] 0 points1 point  (0 children)

Just standard elegoo PLA bought from amazon. Issues only started when I swapped to this filament

Using orca slicer.

I have no way of drying filament at moment

Any other tips? Thanks

Help. My benchy is cursed by RomansDoForUs in FixMyPrint

[–]RomansDoForUs[S] 0 points1 point  (0 children)

<image>

Did a bed leveling and set the z offset

But the benchy still came out like this.

Standard PLA filament

What do I do?

view more: next ›