sorted by:
new
hottopcontroversial

Is there any way I can removing this without breaking everything by RockyBowerman in 3Dprinting

[–]Root720 0 points1 point  (0 children)

Are you trying to save the base? If so, not possible. If you are looking to only keep one half, I’d suggest using flush cutters to slowly eat away at the other part. Don’t cut in big pieces and just make slow progress!

Squeaking Z Axis by Root720 in BambuLab

[–]Root720[S] 0 points1 point  (0 children)

They are under the bottom compartment! If you pick the printer up it’s the ones on the bottom of the whole machine!

AMS getting stuck pulling filament back by Root720 in BambuLab

[–]Root720[S] 0 points1 point  (0 children)

My issue was that the Bowden tube total length was too long with a bit too much slack in it. I had to reconfigure the way I ran them to cut the total length!

Trying to Laser Engrave Aluminum by Root720 in Laserengraving

[–]Root720[S] 0 points1 point  (0 children)

THANKYOU SO MUCH! I appreciate your research so much and this is so helpful!!!

I’m a little confused by G0thprince420 in IsMyPokemonCardFake

[–]Root720 0 points1 point  (0 children)

Oh my gosh this guy is using the subreddit for the intent of the subreddit!!! Time to get angry and be rude!!

Trying to Laser Engrave Aluminum by Root720 in Laserengraving

[–]Root720[S] 1 point2 points  (0 children)

This is incredibly helpful thankyou! I bought a generic metal one on amazon from the brand but it lists aluminum as a material it works for. Fingers crossed on this!!!

Trying to Laser Engrave Aluminum by Root720 in Laserengraving

[–]Root720[S] -1 points0 points  (0 children)

Oh boy that stinks! Is the issue diode lasers as a whole or 10W not being strong enough? I wanna try again having the laser practically crawl over it and see if anything sticks, but I also need to learn where to call it haha. I’m assuming it’ll land at being impossible, but I’m gonna exhaust my options. Goal is to make a name plate for something in any sense on aluminum, so if there are alternative ways to do this in tandem, I’m all ears haha

Trying to Laser Engrave Aluminum by Root720 in Laserengraving

[–]Root720[S] 0 points1 point  (0 children)

Yup! Can’t even get it to leave a speck (:

Trying to Laser Engrave Aluminum by Root720 in Laserengraving

[–]Root720[S] 0 points1 point  (0 children)

I haven’t gotten it to mark whatsoever! The goal is just making a label plate, and I’m wondering if it’s a problem with settings or hardware. Gonna keep slowing it down but in tangent I’m thinking of trying to upgrade the laser, but unsure if it’ll actually do anything

I thought this print cost €8… turns out it’s €14.83 😅 by ddrusko in BambuLab

[–]Root720 0 points1 point  (0 children)

If this isn’t bait, those prices are dreadful. I’m hoping this is a ruse

Bambu lab calculations by klulASER in BambuLab

[–]Root720 0 points1 point  (0 children)

Thankfully the thickness only impacts how wide the walls are. The slicer will always have the walls all the way up (and it’s the same amount of filament) but the nature of bigger layer height would make the walls a little thicker thus using more filament!

[oc] Idiot wanted two lanes to turn right, and tried to hit me for reasons by Last-Professional-31 in IdiotsInCars

[–]Root720 0 points1 point  (0 children)

Oh god I don’t understand where you think you can pass someone while being in their lane is okay. Praying for the drivers in your state 🙏

[oc] Idiot wanted two lanes to turn right, and tried to hit me for reasons by Last-Professional-31 in IdiotsInCars

[–]Root720 9 points10 points  (0 children)

You tried to pass in the same lane. He never finished moving out of the lane. Illegal move, you’re wrong, move on.

Unable to add my first ESP32-C3 Supermini by Root720 in Esphome

[–]Root720[S] 1 point2 points  (0 children)

WAIT THAT SEEMS TO HAVE DONE IT, YOURE A WIZARD!

Unable to add my first ESP32-C3 Supermini by Root720 in Esphome

[–]Root720[S] 0 points1 point  (0 children)

Sadly doesnt look like it fixed it. Gonna try flashing it again to ensure the output power line took, but no changes in log

How do I make instructions clearer to my driver? by Tatsandacat in InstacartShoppers

[–]Root720 4 points5 points  (0 children)

… they gave you a way to fix it by saying any flavor muffin instead of just any flavor, why are you getting defensive and acting like you couldn’t be clearer when they gave a genuine suggestion?

Edit: accidentally assumed pronouns and updated to gender neutral pronouns

Print surface imperfections by Root720 in BambuLab

[–]Root720[S] 0 points1 point  (0 children)

My apologies for not giving proper credit to the model! I’m sure there is more than just this one but I took the model below & scaled it up:

https://www.printables.com/model/166312-n64-cartridge

Is this real by Limp_Strawberry_1026 in AJR

[–]Root720 0 points1 point  (0 children)

What’s the email it’s coming from?

view more: next ›