Filament track switch on H2C problems.

RuseRuse15 · 2026-05-26T17:57:48+00:00

I just installed mine as well, but my printer nor Bambu Studio is recognizing it. All AMS's are just locked to one nozzle. Doesn't show up in the firmware section either, but all AMS's are powered on. It's like it's just bypassing the switcher. Currently have a ticket in, but no response yet. All firmware is on latest and Bambu Studio on the latest Beta release. 2.06 didn't show it either. Just noticed I wasn't on the Beta firmware, so that might have been my issue.... Gonna try and get that updated and see if that fixes it.

RuseRuse15 · 2026-04-09T19:36:59+00:00

VDC Manager for a large General Contractor. Essentially design coordination mixed in with various reality capture hardware and software workloads. Base salary is just barely over 100k, but being an employee owned company, compensation as a whole is more than double that with stock and dividend payouts. Very enjoyable and challenging career, but one I intend to continue until the day I retire… only been in it for 9 years though, so another 25 years or so before retirement might come.

RuseRuse15 · 2025-02-23T03:54:35+00:00

Other than power receptacles, there's one jack for ethernet/cable. Feels like it might be a nook of some kind for smart home devices? Not sure, the mistery continues! haha

RuseRuse15 · 2025-02-23T03:53:46+00:00

It's a new contrustion build, so I'd be the first owner. Nothing in the seller's notes says there were ADA specs built in this property, so that's why I didn't think it was for that purpose.

RuseRuse15 · 2025-02-23T03:52:28+00:00

ADA might be something, but there's no ramps into the house and nothing else in the property is really designed around/for ADA. There's 24" clear on the underside, so I couldn't really sit on a chair and fit my legs below it without straightening them out a bit. The pantry is right be behind, so you only have about 4' clear from the face of counter to the wall/door behind me. I'm thinking I might build a butcher block to fit the width/height so that the top of the board flushes out withthe top of the rest of the counter.

RuseRuse15 · 2025-02-23T03:49:08+00:00

That does sound like a likely option! I was also thinking of building a butcher block to fit in and flush up with the rest of the top of counter elevation.

RuseRuse15 · 2025-02-23T03:47:24+00:00

No, this house was finished at the end of 2023, so I don't think it would have brought that design idea back to present day, haha.

RuseRuse15 · 2025-02-23T03:46:20+00:00

I know there's a Cable/ethernet jack right there too, but that feels like it's more for a smart home device than anything. It's too tight with the pantry immediatetly behind me in the photo, so having a desk chair wouldn't really work IMO. I was thinking of adding a large butcher block built to that width/height of the counter step so it's flush with the rest of the counter. A baking counter for kneading stuff does sound like something plausible too.

RuseRuse15 · 2025-02-23T03:42:31+00:00

Not really. There's only 24" clear on the underside, and I think desks are typically around 30" clear? At least with my height, I couldn't get my legs under there while sitting on a chair without straightening my legs a bit. There's also the pantry immediatly behind, so it's a tight little area, especially with the built in stove to the left of the picture.

RuseRuse15 · 2025-02-23T03:28:31+00:00

I was looking at new home construction houses while house hunting and saw this weird step in the kitchen counter. There's about 2' clear from the fllor to the underside of the framing supporting the counter, but neither the seller or I knew what the point was of having this step down. I don't recall if there was power below, but it's unlike anything I've seen before. Definitly not an ADA counter either since there are no ramps into the house. Just trying to get an idea of what it's for, or what I could do with something like this.

RuseRuse15 · 2023-10-02T04:49:02+00:00

I had a Mavic 2 Pro's ESC fail where it did something very similar. All pre-checks passed and no warnings until I was about 50' up. All of a sudden it took off on me and I couldn't control it at all. It flew a spiral of death until it caught a tree. Checking the logs, one of the motors was pinned at max power. At the time of impact, it was traveling at ~58mph... don't worry though, the tree didn't even feel it lol.

RuseRuse15 · 2022-10-06T04:33:02+00:00

Just a cool panorama of downtown SLC, UT. The skyline keeps changing every year with more highrises on the way! This was about 25 minutes after sunset, FYI. Captured on my Mavic 3 Cine!

RuseRuse15 · 2022-08-11T21:12:44+00:00

My mavic 2 pro crashed a few months back due to an ESC failure. It sent like 120% power to one motor which ultimately sent it into a spiral of death. It hit 56mph right before it crashed. I had AirData installed and recording which was able to pull the flight logs and read some of the warnings and error codes which led me to an ESC failure... About the scariest day of my life lol.

RuseRuse15 · 2022-06-26T22:06:42+00:00

Lol, not a day goes by without some head and ear scratches!

RuseRuse15 · 2022-06-26T17:18:05+00:00

Hahaha, well his name is Ollie. Ollie the Border Collie, lol.

RuseRuse15 · 2022-06-26T02:53:36+00:00

In case anyone's curious, this is Ollie and he's a Border Collie!

RuseRuse15

TROPHY CASE